Service After First 5 Hours | Snapper HZT21480BV, CZT19480KWV

Section 4 - MAINTENANCE

4.1INTRODUCTION

To retain the quality of the SNAPPER mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular SNAPPER mower, always mention the model and serial number. SNAPPER recommends returning the mower to an authorized SNAPPER dealer annually for inspection and addition of any new devices, which might upgrade the safety of the mower. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

4.2SERVICE - AFTER FIRST 5 HOURS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid serious burns; allow sufficient time for all parts to cool.

4.2.1.CHANGE ENGINE OIL Change engine oil as follows:

1. Place a 4 quart minimum capacity container under the end of the oil drain.

2. Rotate counter clockwise and pull out to open the drain plug. See Figure 4.1.

ROTATE PLUG COUNTER CLOCKWISE

THEN PULL OUT TO DRAIN OIL

FIGURE 4.1

3.After all the oil has drained, close the drain by pushing in and rotating clockwise to close. Wipe up any oil that may have spilled. Dispose of drained oil properly. See Figure 4.1.

4.Fill engine crankcase with new oil. Refer to your engine owner’s manual for oil specifications.

5.Change engine oil filter at every oil change. Refer to your engine owner’s manual for service instructions.

4.2.2. CHECK MOWER BLADE

1.Stop Engine. Remove key. Disconnect spark plug wire(s) and secure away from spark plug(s).

2.Engage parking brake.

3.Use a hydraulic floor jack or hoist to raise machine high enough to gain access to the underside of deck. Secure machine with safety blocks.

WARNING

Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. DO NOT use a cutting blade that shows signs of excessive wear or damage. Refer to Section “MOWER BLADE REPLACEMENT” for proper blade inspection and service procedures.

4.Check torque of blade mounting bolts. As necessary, torque to 70 to 80 ft. lbs. See Figure 4.2.

5.Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

6.Check blade for straightness.

CHECK BLADE MOUNTING BOLTS - TORQUE SHOULD BE 70 TO 80 FT. LBS.

FIGURE 4.2

HZT21480BV, CZT19480KWV, CZT19480KWV, CZT19481KWV, HZT21480BV, HZT21481BV specifications

The Snapper CZT19480KWV, CZT19481KWV, HZT21480BV, HZT21481BV, and HZT21480BV represent a lineup of advanced zero-turn lawn mowers designed for both residential and commercial users. These models are renowned for their robust performance, user-friendly features, and technological innovations that enhance mowing efficiency and comfort.

One of the standout features of these Snapper models is their powerful engine options. The CZT19480KWV and CZT19481KWV are equipped with dependable Kawasaki engines, delivering exceptional torque and speed for tackling dense grass with ease. Similarly, the HZT21480BV and HZT21481BV models are powered by reliable Briggs & Stratton engines, ensuring consistent performance under various mowing conditions.

The zero-turn capability is a defining characteristic of these mowers, allowing for unparalleled maneuverability. This feature enables operators to navigate tight spaces and obstacles with minimal effort, resulting in a pristine cut and reduced mowing time. The precision steering controls enhance the operator's ability to make sharp turns while maintaining a consistent cutting height.

Comfort is prioritized in the design of these models. The mowers come with ergonomic seating, providing substantial back support for extended mowing sessions. Additionally, the adjustable steering levers allow users to customize their driving position, contributing to a comfortable and efficient mowing experience.

In terms of cutting performance, the Snapper models boast high-quality cutting decks, ranging from 48 to 52 inches, made of durable steel. The decks are engineered for a clean cut and can efficiently handle various grass types and heights. The mowing height is easily adjustable, offering multiple settings to accommodate different lawn conditions.

Technologically, these mowers incorporate advanced features like an intuitive control panel, easy-start ignition systems, and optional accessories, such as mulching kits and baggers, providing versatility for lawn care needs. Furthermore, the Snapper Quick Turn technology enhances the overall efficiency, cutting down the time spent mowing while ensuring even grass distribution.

In summary, the Snapper CZT19480KWV, CZT19481KWV, HZT21480BV, HZT21481BV, and HZT21480BV combine power, precision, and comfort, making them ideal choices for users seeking reliable and efficient zero-turn mowers. Whether for residential lawns or commercial landscaping, these models offer the performance and features that meet the demands of any mowing task.