Snapper 7800784, 7800785, 7800786, 7800787 Move lever to the on position, Adjust side to side level

Page 33

 

 

 

 

 

 

 

 

Troubleshooting

 

 

 

 

 

PROBLEM

PROBABLE CAUSE

 

 

CORRECTIVE ACTION

 

 

 

 

Rider Will Not

1. Drive disc worn or damaged.

1.

Replace drive disc.

Move Or Loss

 

 

 

2. Rubber drive disc is not tracking properly on

2.

Adjust rubber drive disc.

of Traction

drive disc.

 

 

 

 

 

 

 

 

 

 

 

 

3.

Tapered axle bolt and nut missing.

3.

Replace with tapered bolt & nut.

 

 

 

 

 

 

 

4.

Axle bearing seized.

 

4.

Contact authorized dealer.

 

 

 

 

 

 

5.

Insufficient lubrication in chain case or

5.

Contact authorized dealer.

 

transmission/differential.

 

 

 

 

 

 

 

 

 

Blade(s) Not

1. Blade engagement lever in the “OFF” position.

1.

Move lever to the “ON” position.

Cutting

 

 

 

 

2. Mower belt slipping.

 

2.

Adjust or replace mower belt.

 

 

 

 

 

 

3.

Cutting blade is dull, worn or damaged.

3.

Sharpen or replace cutting blade.

 

 

 

 

 

Cutting Grass

1. Uneven tire pressure.

 

1.

Bring to proper pressure. 15 PSI front tire & 12 PSI

Improperly

 

 

 

 

rear tire.

 

 

 

 

 

 

 

 

2.

Cutting height too low or high.

2.

Adjust cutting height.

 

 

 

 

 

 

 

3.

Engine speed too slow.

 

3.

Move throttle control to “FAST” position.

 

 

 

 

 

 

 

4.

Forward speed too fast.

 

4.

Move transmission shift lever to a slower speed.

 

 

 

 

 

 

 

5.

Terraced cut, side to side.

 

5.

Adjust side to side level.

 

 

 

 

 

 

6.

Excessive deck pitch, front to rear.

6.

Adjust front to rear pitch.

 

 

 

 

 

 

7.

Cutting blade(s) dull or damaged.

7.

Sharpen cutt ng edges or replace blade(s).

 

 

 

 

 

 

 

 

 

8.

Mower belt slipping.

 

8.

Adjust

ens

n r replace mower belt.

 

 

 

 

 

 

 

Poor Grass

1. Engine speed too slow.

 

1.

Move

hro

le control to “FAST” position.

Discharge

 

 

 

 

 

2. Forward speed too fast.

 

2.

Move

ransmission shift lever to a slower speed.

 

 

 

 

 

 

 

 

3.

Grass is wet.

 

 

3.

Mow when grass is dry.

 

 

 

 

 

 

4.

Excessively dull, worn or damaged blade(s).

4.

Service mower blade.

 

 

 

 

 

 

5.

Build up of grass clippings and debris un er

5.

Clean the underside of deck.

 

deck.

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Improper blade installed

deck.

6.

Install proper blades.

 

 

 

 

Oil Leaking

1. Leaking chain case or differential lugs.

1.

Verify plugs are not cracked & are in good shape.

 

 

 

 

 

Check gaskets.

 

 

 

 

 

 

 

2.

Leaking engine block.

 

2.

Contact authorized dealer.

 

 

 

Reproduction

33

Image 33
Contents Manual No Rev. ‘-’ Not ForEngine EquipmentTable of Contents Protection for Children Protection against Tipovers Operator SafetyPreparation From Previous ColumnSafe Handling of Gasoline Protection against Tipovers OperationTowing Maintenance Remove Battery Before Starting Height of Cut Safety PanelDecal Identification Battery Warning Reverse LockoutParking Brake Park Brake Latch Fuel Tank Features and ControlsTo avoid damaging the emissions system Operation Before StartingEngine Electric Start Operation Starting and OperationCarefully Make certain the Blade Lever A, is OFF position Start, release the key, make sure the Clutch/Brake Pedal isEngine Manual Start Housing. Never allow rope to snap backMower Blade Wheel DriveReproduction Figu Engagi g the clutch/brake pedal Stopping Engine Wheel Drive, Blade OperationFigu 15 St ppi g the mower blade ProceRe 18 Cutting height adjustment Cutting Height AdjustmentStopping Engine, Wheel Drive BladeReverse Lockout Mechanism Override Reverse Lockout MechanismAte blades in reverse. Stop BLADES, Look and see While backingTractor and Mower Engine Maintenance Maintenance ChartService Engine Air Cleaner MaintenanceCheck Mower Blade Change Engine OilService Brake / Park Brake Check the Blade Drive BeltBlade Brake Check Engine Safety Interlock System ChecksReverse Lockout Mechanism Lubrication Grease FittingsMower Deck Levelness Clean Mower Deck Mower Deck Linkage LubricationFront Wheel Bearing Lubrication Mower Blade Spindle LubricationRear Axle Bearing Lubrication Additional engine serviceInspect for lubricant on the internal parts Replace with a new plugStorage Out of Season Fuel FilterRepro Duction Avoi Damaging the emissions system Blade Brake Adjustment Engine Adjustments and RepairAutomatic Blade Brake should stop the blades wi hin Re 31 Measuring blade brake clearanceMower Deck Adjustment Front-to-Rear Levelness Mower Deck Adjustment Side-To-Side LevelnessEs ot have slack adjustment Mower Drive Belt AdjustmentRemove the mower drive belt cover. Refer to the sec Tion entitled Check Mower Drive BeltBottom of the housing Service Brake / Park Brake AdjustmentRear Engine Rider Drive Components Measurement should be 3/4Blade Wear Limits Mower Blade ReplacementBelt Replacement Mower Drive Belt ReplacementBelt Removal Ut ng f 30 inch decksBattery Removal BatteryBattery Installation Fig re 49 Battery connectionsBattery Charging Battery StorageCharge the battery. Refer to the section entitled Troubleshooting Move lever to the on position Adjust side to side levelWarranty Period WarrantySlope Guide Common Service Parts Power Rating2811524BV 2812524BVE 3014524BVE 3317524BVE

7800787, 7800786, 7800784, 7800785 specifications

The Snapper 7800 series, which includes models 7800787, 7800784, 7800785, and 7800786, represents a remarkable advancement in lawn care technology and design. These mowers are engineered for efficiency, durability, and ease of use, making them popular among both residential and commercial users.

One standout feature across the Snapper 7800 series is the powerful Briggs & Stratton engine. This reliable engine is designed for optimal performance, enabling users to tackle even the toughest mowing tasks. With a range of horsepower options, each model provides ample power to handle various grass lengths and terrains, ensuring a clean and consistent cut every time.

The cutting deck on these models is another highlight. Snapper has integrated a robust, high-quality steel deck that not only promises longevity but also aids in superior grass handling. With a cutting width that varies by model, users can choose the size that best fits their lawn's dimensions. Additionally, the adjustable cutting height allows for customization, enabling users to achieve the perfect lawn finish.

Snapper's innovative engineering extends to its ergonomic design. The handles on the 7800 series are designed for comfort and usability, featuring easy-to-grip materials and adjustable heights to accommodate users of all sizes. This attention to user comfort reduces fatigue, ensuring that lawn maintenance can be completed efficiently.

Another impressive aspect is Snapper's commitment to technology. Some models in the 7800 series feature advanced self-propelling systems, allowing for effortless maneuvering over uneven terrain. The ease of use doesn’t stop there; these mowers come with a simple pull-start mechanism, and some models even offer an electric start option for added convenience.

In terms of maintenance, the Snapper 7800 series is designed to be user-friendly. The easy-access design makes routine maintenance tasks, such as oil changes and air filter replacements, straightforward. This emphasis on straightforward upkeep helps ensure that the mower can operate at peak efficiency throughout its lifespan.

In conclusion, Snapper's 7800787, 7800784, 7800785, and 7800786 models collectively embody the future of lawn care technology. Their powerful engines, durable construction, ergonomic designs, and user-friendly features make them exceptional choices for anyone looking to maintain a pristine lawn. These mowers not only offer efficiency but also deliver results that homeowners and professionals alike can take pride in. Whether for residential use or commercial landscaping, the Snapper 7800 series stands out as a top-tier option in the mowing market.