Snapper 355Z manual Hour Meter, PTO Switch, Transmission Oil Fill, Transmission Release Levers

Page 19

Hour Meter

The hour meter measures the number of hours the key has been in the RUN position.

Note: The hour meter will register the passage of time when the key is in the RUN position, even if the engine is not running. The hour meter has a self contained power source so the total hours are always visible.

PTO Switch

The PTO (Blade Engage) switch engages (turns the blades on) and disengages (turns the blades off) the mower deck. To engage the PTO, pull UP on the switch. Push DOWN to disengage. Note that the operator must be seated firmly in the rider seat for the PTO to function.

Transmission Oil Fill

Transmission oil is added through the transmission oil reservoirs. It also serves as extra holding capacity for oil as the transmissions heat up and the oil expands. See CHECK TRANSMISSION OIL LEVEL for oil level check and fill procedures.

Transmission Release Levers

The transmission release levers deactivate the transmissions so that the unit can be pushed by hand. See PUSHING THE UNIT BY HAND for operational information.

Seat Adjustment Lever

The seat can be adjusted forward and backward. Move the adjustment lever towards the left, slide the seat to the desired position, and release the lever.

Fuel Tank

Fuel Level Gauge

To remove the cap, turn counterclockwise. The fuel gauge is mounted in the fuel tank and indicates the amount of fuel in the tank.

Mower Height of Cut Adjustment

To adjust cutting height, pull the large lever back fully to lock the control in the attachment raised transport position. Position the cutting height selector pin on the appropriate hole to achieve the desired cutting height. Pull back on the small lift latch lever and large lever simultaneously, and lower the mower into cutting position.

For attachment transport lift, pull the large lift lever back fully to lock the control in the attachment raised transport position.

Parking Brake

DISENGAGE	Releases the parking brake.
ENGAGE	Locks the parking brake.

Pull the parking brake lever back to engage the parking brake. Move the lever fully forward to disengage the parking brake. NOTE: To start the unit the parking brake must be engaged.

17

Image 19

Contents OPERATOR’S Manual Engine Where to Find Us MowerDate Purchased Table of Contents Read the Manual Safety Operating SafetyChildren Thrown Objects Slope OperationMoving Parts Retaining Walls, Drop-offs, and Water Fuel and MaintenanceEnclosed Areas Important cautions or warnings which must be followed Wear hearing protection when operating this machineGeneral Operation Transporting and StorageEmissions Slope OperationTowed Equipment RIDE-ON Units ChildrenService & Maintenance Service and MaintenanceSafe Handling of Gasoline 5100093 Decal Safety DecalsIdentification Tags North American Models Operational Safety ChecksAbcde KLM no Pqrst Safety IconsParts Bag Contents AssemblyLever Alignment Adjustment Install the Ground Speed / Steering Control LeversAs shown in Figure Repeat process for other side of unit Seat Adjustment Seat & Safety Switch AssemblySeat Position Adjustment Battery Safety Rules Charge The BatteryCheck Tire Pressures How to Prepare the EngineTire Pressure Ground Speed / Steering Control Levers Features and ControlsIgnition Switch Control FunctionsHour Meter PTO SwitchSeat Adjustment Lever Mower Height of Cut AdjustmentOperation General Operating SafetyChecks Before Starting Pushing the Rider by Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the Rider and EngineReverse Travel Practice Zero-Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnReinstall the mower deck guards Mower Removal and InstallationInstallation Install the roller bar connecting rod M and the hair pinTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassAlways start mowing on a smooth, level area When and How Often to MowMowing Patterns Mowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingEngine Maintenance Items MaintenanceSafety Items Rider Maintenance ItemsControl handle pivots Discharge chute hinge LubricationGrease OilMower blade is bent or broken Servicing The Mower BladesInspecting the Mower Blades Never weld or straighten bent mower bladesBalancing the Mower Blade Nail Reinstalling the Mower BladesFuel Filter Engine Maintenance Adding FuelChange Engine Oil & Filter Oil Drain Tube Oil Filter Cap Change Engine Oil & FilterChange Interval Every 200 Hours Check / Fill Transmission OilTransmission Oil Filter Change Oil Type 20W-50 conventional detergent motor oilBattery Charging Battery Maintenance Cleaning the Battery and CablesStorage Cutting Height Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake Adjustment Blade Brake Check PTO Clutch AdjustmentMower Deck Leveling Perform these adjustments on a flat level surfaceBelts Over Pulleys Mower Belt ReplacementReinstall the PTO drive belt Hydraulic Pump Drive Belt ReplacementTroubleshooting the Rider Troubleshooting WarningTroubleshooting the Mower Rider TroubleshootingStreaking Troubleshooting Common Cutting Problems355ZB2654 SpecificationsProduct Specifications Engine Power Rating InformationIndentification Disclaimer of Warranty Year Limited Warranty