Snapper 355Z manual Speed Balancing Adjustment, Cutting Height Adjustment, Neutral Adjustment

Page 36

Speed Balancing Adjustment

WARNING

DO NOT adjust the rider for a faster overall speed forward or reverse than it was designed for.

If the rider veers to the right or left when the ground speed / steering control levers are in the maximum forward or reverse position, the top speed of each of these levers can be balanced by turning the adjustment bolt(s) (A & C Figure 35). Only reduce the speed of the wheel that is traveling faster.

TO REDUCE THE SPEED OF THE FASTER WHEEL

1.Loosen the jam nut securing the top speed adjustment bolt (A, C).

2.Turn the top speed adjustment bolt COUNTER- CLOCKWISE to reduce the speed.

3.Retighten the securing nut when adjustment is complete.

C

A

B

Figure 35. Top Speed Adjustment

A.Forward Top Speed Adjustment Bolt

B.Control Lever Base

C.Reverse Top Speed Adjustment Bolt

Cutting Height Adjustment

The cutting height adjustment pin (A, Figure 36) controls the mower cutting height. The cutting height is adjustable between 1-1/2” (3,8 cm) and 4-1/2” (11,4cm). Pulling the lever back fully locks the control in transport position.

To adjust cutting height:

1.Pull the adjustment lever (B) back fully until it locks in transport position.

2.Remove the cutting height adjustment pin (A) and insert it into the desired hole.

3.Pull back on the adjustment lever (B), squeeze the smaller transport release lever (C), and allow the lever to move forward until it is supported by the cutting height adjustment pin (A).

Neutral Adjustment

If the unit creeps forward or backward with the control levers in their neutral positions, contact Snapper at 1-800-317- 7833.

C

B

A

Figure 36. Cutting Height Adjustment

A.Cutting Height Adjustment Pin

B.Deck Lift / Cutting Height Lever

C.Transport Release Lever

34	www.snapper.com

Image 36

Contents OPERATOR’S Manual Where to Find Us Mower EngineDate Purchased Table of Contents Safety Operating Safety Read the ManualChildren Slope Operation Thrown ObjectsMoving Parts Fuel and Maintenance Retaining Walls, Drop-offs, and WaterEnclosed Areas Wear hearing protection when operating this machine General OperationTransporting and Storage Important cautions or warnings which must be followedSlope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsService and Maintenance Service & MaintenanceSafe Handling of Gasoline Safety Decals 5100093 DecalOperational Safety Checks Identification Tags North American ModelsSafety Icons Abcde KLM no PqrstAssembly Parts Bag ContentsInstall the Ground Speed / Steering Control Levers Lever Alignment AdjustmentAs shown in Figure Repeat process for other side of unit Seat & Safety Switch Assembly Seat AdjustmentSeat Position Adjustment Charge The Battery Battery Safety RulesHow to Prepare the Engine Check Tire PressuresTire Pressure Features and Controls Ignition SwitchControl Functions Ground Speed / Steering Control LeversPTO Switch Seat Adjustment LeverMower Height of Cut Adjustment Hour MeterGeneral Operating Safety OperationChecks Before Starting Insert the key into the ignition switch and turn it to Starting the EngineStopping the Rider and Engine Pushing the Rider by HandZero-Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsMower Removal and Installation InstallationInstall the roller bar connecting rod M and the hair pin Reinstall the mower deck guardsMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing PatternsMowing Methods Proper Broadcast Mowing Always start mowing on a smooth, level areaProper Mulching Attaching a TrailerMaintenance Safety ItemsRider Maintenance Items Engine Maintenance ItemsLubrication GreaseOil Control handle pivots Discharge chute hingeServicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Mower blade is bent or brokenReinstalling the Mower Blades Balancing the Mower Blade NailEngine Maintenance Adding Fuel Fuel FilterChange Engine Oil & Filter Change Engine Oil & Filter Oil Drain Tube Oil Filter CapCheck / Fill Transmission Oil Transmission Oil Filter ChangeOil Type 20W-50 conventional detergent motor oil Change Interval Every 200 HoursBattery Maintenance Cleaning the Battery and Cables Battery ChargingStorage Speed Balancing Adjustment Cutting Height AdjustmentNeutral Adjustment Parking Brake Adjustment PTO Clutch Adjustment Blade Brake CheckPerform these adjustments on a flat level surface Mower Deck LevelingMower Belt Replacement Belts Over PulleysHydraulic Pump Drive Belt Replacement Reinstall the PTO drive beltTroubleshooting Warning Troubleshooting the RiderRider Troubleshooting Troubleshooting the MowerTroubleshooting Common Cutting Problems StreakingSpecifications Product SpecificationsEngine Power Rating Information 355ZB2654Indentification Year Limited Warranty Disclaimer of Warranty