Snapper 281123BVE (84874), 2812523BVE (7085622), 281123HVE (84883) manual For use with 7075071 seat

Page 55

ELECTRICAL SYSTEMS (For 13.5, 15, 16 & 17HP Briggs)

Item

Part No

Qty

Description

Note

1

7060753

1

KIT, 12 Volt Dry Charge Battery, 220 CCA

 

2

7075671

1

SOLENOID, Super-Trombetta

 

3

7022788

1

HARNESS, Starter Wiring (Briggs)

 

4

7074406

1

HARNESS, Ignition Wiring (Briggs)

 

5

7016168

1

HOLDER, Fuse (Includes Fuse)

 

--

7016169

1

FUSE, 10 Amp (Not shown)

 

6

7063064

1

INTERLOCK MODULE, Briggs & Kohler

was 28606

7

7028386

1

HARNESS (Deck Interlock Wiring)

 

8

7018524

1

SWITCH, Deck Interlock (NO)

 

9

7012444

1

COVER, Battery Cable

 

10

7019326

1

WIRE, Positive (Red, 17” long)

 

11

7026343

1

SWITCH, Ignition-Afterfire Solenoid

 

12

7090880

1

WASHER, 5/8” Internal Tooth Lock

 

13

7015438

1

NUT, 5/8-32 Hex

 

14

7011138

1

IGNITION KEY, Pair

 

15

7090539

3

SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap

 

16

7022886

1

SWITCH, Operator Presence Control (OPC) Traction (NC/NO)

 

17

7091576

4

NUT, 1/4-20 Hex, GR 5 or B

 

18

7090053

2

WASHER,1/4” Internal Tooth Lock

 

19

7027172

2

SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5

 

20

7028027

1

WIRE, Negative, Black (15” long)

 

21

7028675

1

HARNESS, Operator Presence Control (OPC) Wire

 

22

7091576

4

NUT, 1/4-20 Hex, GR 5 or B

 

23

7012080

2

CABLE TIE, 7”

 

24

7090372

2

NUT, 1/4-20 Hex Center Lock, GR 5 or B

 

25

7014451

1

CABLE TIE

 

26

7012485

2

RETAINER, 1/4” Bolt

 

27

7023354

1

SWITCH, Seat (NC)

for use with 7075071 seat

Footnotes:

REAR ENGINE RIDER

 

Manual No.

7006152

SERIES 23

55

TP 400-5003-5-RE-N

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Rear Engine Rider Series Page Table Of Contents WHEELS- Front & Rear Used on 8, 10, 11.5, 12.5 Includes Items 2, 3, 4, 5Includes Items 5, 14 10 HPFront END, Steering Used on 33 & 42 Decks Includes itemReplaces 7072648 voided Used on 25, 28 & 30 DecksFront END, Steering Front END, Steering Main Case & L.H. Fender Used on Euro models only Replaces 7022509 voidedUsed on E331523KVE Model OnlyMain Case & L.H. Fender Cross Brace Used on 331723BVE Model onlyLeft Hand Fender & Bearing Or quantity as required BEARING, DXDIFFERENTIAL, R. H. Fender Properly to prevent binding Includes 1-1/8 I.D. DX bearingDIFFERENTIAL, R. H. Fender 7075479 KIT, Long & Short Axle Includes items 23, 24 Yoke Lift Components Fender WASHER, 5/16 Primary Chain Case & Smooth Clutch Or 7090480, center lock flange Includes the following 16 itemsIncludes the following 5 items Replaces 7054243 voidedGear Shifter Assembly Assy Part of Speed Adjustment LatchUsed with Fuel Tank & Seat Used on 9, 10 & 11.5HP Models Used on 12HP & Higher ModelsUsed on 2811523BV 3011523BVENGINE, MUFFLER, Drive Disc Used on 33 Deck Models Recoil startElectric start Used on 28 & 30 DecksCutting DECKS, Deflector 28 & 33 Hi-Vac Incl. items 15, 16, 18, 19 Painted deck w/decals & wheelBracket fasteners Painted deck with decalsCutting DECKS, Deflector 28 & 33 Hi-Vac Used on 28 & 33 Decks Cutting DECK, Deflector Or 7091518 3/8-24 Hex Nyloc BELTS, BRAKES, Interlock Used on 33 Deck Models only BELTS, BRAKES, Interlock BELTS, BRAKES, Interlock RAILS, Lift ARMS, CAM Lift RAILS, Lift ARMS, CAM Lift RAILS, Lift ARMS, CAM Lift Anchor Blade Stop Pedals Replaces 7035669 .062 dia Spindle Used on 33 deck Decals DECAL, Snapper Not shown, not a service partElectrical Systems For 9, 11 & 11.5HP Briggs Recoil Used on 11-1/2 HP Engines Used on 11 & 13 HP EnginesElectrical Systems For 10, 11, 12, 12.5 & 13HP Briggs Used on 11 & 13HP Engines ReplacesUsed on 12.5 & 13 HP Briggs Electrical Systems For 13.5, 15, 16 & 17HP Briggs For use with 7075071 seat Electrical Systems For 11 & 13HP Honda Purchase from engine No Snapper part numberManufacturer Electrical Systems For 15HP Kohler Replaces Electrical Systems Briggs Magneto Ground Electrical Systems Briggs Magneto Ground Electrical Systems Kohler Magneto Ground View shows engine magneto ground area Wiring Schematic 9, 11 & 11.5HP Recoil Start Briggs Wiring Schematic incl. harness #s 7028386, 7073714 Wiring Schematic 10, 11, 12, 12.5 & 13 HP Briggs Wiring Schematic incl. harness #s 7022788, 7073715 Wiring Schematic 13.5, 15, 16 & 17 HP Briggs Engines Wiring Schematic incl. harness #s 7022788, 7074406 7015430 Wiring Schematic 11 & 13 HP Honda Engines Wiring Schematic incl. harness #s 7054589, 7074962 7074963 Wiring Schematic 14 & 15 HP Kohler Engines Wiring Schematic incl. harness #s 7019321, 7074405 7028678 Hardware Bags For manual start models Hardware Bags Hardware Bags Accessories & Attachments Models Used on All RER AluminumDrive Discs Used on All series 7 & NewerPage Page Rear Engine Rider Series

301123BV (84873), 301123BV (84941), 281023BVE (84871), 281123BV (84872), 281123BVE (84874) specifications

The Snapper 2813523BVE (85624), 2811523BV (7084940), 281123BV (84872), 281223BVE (85622), and 281123HVE (84883) represent a versatile range of outdoor power equipment that embodies the combination of performance and innovation that Snapper is known for. These models cater to a wide array of landscaping needs, making them suitable for both residential and commercial applications.

One of the main features of these Snapper models is their powerful engines. They are equipped with robust motors that provide ample torque and speed, enabling users to tackle various mowing conditions with ease. The engines are designed for fuel efficiency and low emissions, making them environmentally friendly choices for lawn care.

These models also showcase advanced cutting technologies. With multiple cutting heights adjustable with ease, users can achieve the perfect lawn finish. The decks on these models are engineered for enhanced airflow, ensuring a clean and efficient cut. Additionally, the side-discharge, mulching, and bagging options provide flexibility to accommodate different mowing preferences and yard conditions.

Another standout feature of the Snapper models is their user-friendly design. Each model is equipped with ergonomic handles that provide comfort during operation, reducing user fatigue. The intuitive controls and robust wheels enhance maneuverability, making it easier to navigate through tight spots and uneven terrain.

Furthermore, durability is a significant characteristic of the Snapper 281 series. Built with heavy-duty materials, these lawn mowers are designed to withstand the rigors of regular use, ensuring longevity and reliability. They also require minimal maintenance, allowing users to spend more time enjoying their lawns rather than maintaining equipment.

Safety is another priority in the design of these models. They come equipped with features such as blade brakes and safety switches, which are crucial in preventing accidents during operation. Users can operate with confidence knowing that safety measures are in place.

In summary, the Snapper 2813523BVE (85624), 2811523BV (7084940), 281123BV (84872), 281223BVE (85622), and 281123HVE (84883) represent a comprehensive solution for outdoor maintenance. With their powerful engines, advanced cutting technologies, user-friendly design, durable construction, and emphasis on safety, these models stand out in the competitive market of lawn care equipment, providing a reliable and efficient option for users looking to maintain their landscapes effectively.
Top Page Image Contents