Snapper 3011523BV specifications Stopping Engine Wheel Drive, Blade

Page 12

Operation (Continued)

!

WARNING

!

DO NOT leave the machine with the engine running. STOP Blade. STOP engine. Shift to neutral and engage park brake. Remove key.

Mower Blade

1.Stop the mower blade by releasing the blade pedals (A, Figure 15) or moving the blade lever (B) rearward to the “OFF” position.

Stopping - Engine,

Wheel Drive, Blade

Engine

1.Stop the engine by turning the key (A, Figure 13) to the “OFF” position.

Operation	A

Figure 13: Turning key to ‘Off’

Wheel Drive

1.Stop motion of the Rear Engine Rider by pushing the clutch/brake pedal (A, Figure 14) all the way down to apply the brake.

B

A

Figure 15: Stopping the mower blade

!

WARNING

!

Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment pro- cedures or return machine to an authorized SNAPPER deal- er for adjustment. DO NOT CONTINUE to operate machine until blade brake is adjusted and functioning properly.

A

Figure 14: Engaging the clutch/brake pedal

10	www.snapper.com

Image 12

Contents Series Date of Purchase Retailer Retailers Phone Number Equipment EngineSnapper is a trademark Simplicity Manufacturing, IncTable of Contents Protection for Children Protection against TipoversPreparation Do not allow pre-teenage children to operate machineSafe Handling of Gasoline OperationMaintenance TowingFeatures and Controls Features and ControlsFuel Tank OPERATOR’S Seat Adjustment Operation Pre-Start Check ListFuel filler cap A, is tight, and the vent B is Operation Starting and Operation Engine Electric StartEngine runs smooth On Next OperationSetting the park brake Engine Manual StartOperation Mower BladeWheel Drive Stopping Engine Wheel Drive, Blade Stop the engine by turning the key A, to the OFF positionCutting Height Adjustment Operation Stopping Engine, Wheel DriveBlade Park BrakeOperation Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideAte blades in reverse. Stop BLADES, Look and see While backingMaintenance Service After the First 5 HoursIntroduction Service Brake / Park Brake Blade Drive Belt ReplacementCheck the Blade Drive Belt Blade BrakeSafety Interlock System Checks Check EngineReverse Lockout Mechanism Lubrication Grease FittingsService Every 25 Operating Hours Engine Service Rear Axle Bearing LubricationDifferential / Chain Case Lubrication Service Annually Every Two YearsStorage Out of Season Removing the Fuel TankEngine Adjustments and Repair Mower Deck and Component AdjustmentsBlade Brake Adjustment Reinstall the belt cover and tighten the bolts securelyMower Deck Adjustment Side-To-Side Levelness Mower Deck Adjustment Front-to-Rear LevelnessMower Drive Belt Adjustment For 28 & 30 Decks Only Service BRAKE/PARK Brake AdjustmentMove the blade lever up and over to the on position To the rear main caseRear Engine Rider Drive Components Measurement should be 3/4Mower Blade Replacement Blade Wear LimitsSigns of excessive wear or damage Blade Sharpening Belt Replacement Belt RemovalRemove the idler A, Figures 46 Battery Battery RemovalBattery Installation Slide the battery partially into the battery housingBattery Service Battery StorageNew Battery Preparation Battery TestingSnapper Rear Engine Rider Accessories Battery Condition ChartDescription of Kit Models Used on Maintenance Service Schedule SeasonMaintenance Maintenance/Replacement Parts Troubleshooting Problem Probable Cause Corrective ActionStop Move lever to the on position Year Limited Warranty Slope Guide Page Page Page Page Product Specifications Common Service Parts2811523BV 2812523BVE Snapper Products Macon Street McDonough, GA