Snapper ELP21702BV Operating Instructions, 2.2.ENGINE & BLADE, Choke Models Recoil Start, Figure

Page 7
FIGURE 2.4

Section 2 - OPERATING INSTRUCTIONS

2.2STARTING & OPERATION 2.2.2. ENGINE & BLADE (Primer Models) (Electric Start)

When the ignition key is turned to “START”, the engine will not crank over and will not start unless the blade control is engaged!

1. Move engine speed control to the “Fast” (Rabbit) position. See Figure 2.4.

2. Push primer button three times to start a cold engine. NOTE: Do not use primer button to start warm engine.

3. Pull blade control against handle.

4. Turn key to the start position until engine starts. See Figure 2.4.

NOTE: If after 5 seconds of cranking the engine does not start, release the key and attempt starting again after waiting for approximately 20 seconds.

5.After engine starts, allow a brief warm-up until engine runs smooth.

BLADE

CONTROL

FAST

IGNITION

KEY

FIGURE 2.4

2.2.2.ENGINE & BLADE

(Choke Models) (Recoil Start)

1. Open fuel valve located at the top rear of engine (Kawasaki engines).

2. Move engine speed control to the “CHOKE” position. See Figure 2.3.

IMPORTANT: Stop the engine (and blade) by releasing blade control.

3. Pull blade control against handle.

4. Pull rope start handle to crank engine.

5. After engine starts, move engine speed control to the “FAST” (Rabbit) position and allow a brief warm up until engine runs smooth.

2.2.3.PROPELLING MOWER

1.Move ground speed control to the desired speed position. See Figure 2.5.

2.Move wheel drive control against handle to engage wheel drive and propel mower forward.

IMPORTANT: Forward motion of machine must be stopped before changing position of the ground speed control. See Figure 2.5.

WHEEL DRIVE

GROUND

CONTROL

SPEED

 

CONTROL

ENGINE

SPEED

CONTROL

FIGURE 2.5

2.3STOPPING

Stop engine and blade by releasing the blade control. Stop forward motion of mower by releasing the wheel drive control.

2.4HANDLE HEIGHT ADJUSTMENT

The height of the mower handle can be adjusted as follows:

1. Loosen the lower nuts on each lower handle as shown in Figure 2.6.

LOOSEN NUTS

TO ADJUST

HANDLE BAR

FIGURE 2.6

2.Move upper mower handle up or down until the desired position is achieved.

3.Tighten the nuts on each lower handle bracket to maintain desired position. Torque nuts to 15 to 25 ft. lbs.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents SELF-PROPELLED MODEL ELP21702BV Safety Instructions & Operator’s Manual forPREPARATION IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN SLOPE OPERATIONOPERATION MAINTENANCE AND STORAGETABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATIONFIGURE 1.1 INTRODUCTIONPrimer Models Recoil Start Section 2 - OPERATING INSTRUCTIONS2.1PRE-STARTCHECK LIST 2.2STARTING & OPERATION 2.2.1. ENGINE & BLADE2.2.3.PROPELLING MOWER 2.4HANDLE HEIGHT ADJUSTMENTFIGURE 2.2.2.ENGINE & BLADE Choke Models Recoil Start2.5CUTTING HEIGHT ADJUSTMENT 3.2.3. WHEEL DRIVE CONTROL Section 3 - MAINTENANCE3.1INTRODUCTION 3.2.2. GREASE LEVEL IN TRANSMISSION3.2.4. CHECK MOWER BLADE Section 4 - REPAIR & ADJUSTMENTS CUTTING EDGE OF THUMBWHEEL ADJUSTERDO NOTSHARPEN BEYOND ORIGINAL4.3BELT SERVICE Section 4 - ADJUSTMENTS & REPAIR Battery Condition Chart Start Using TROUBLESHOOTINGPROBLEM Using Recoil StarterMAINTENANCE/REPLACEMENT PARTS MAINTENANCE PARTS MAINTENANCE SCHEDULE1 WARNING INSTRUCTIONS DECAL IDENTIFICATION8HEIGHT CONTROL INSTRUCTION: Shows direction of movement of HEIGHT ADJUST HANDLE to select a change in height if cut from highest cutting height clockwise to the lowest height counter- clockwise. Note that there is a total of eleven heights of cut CHUTE DEFLECTOR DECAL P/N AIR FILTER SYMBOL P/NDECAL P/N 2 YEAR LIMITED WARRANTY NOTES NOTES SERIES EUROPEAN 21” CAST ALUMINUM DECK WALK MOWERS
Top Page Image Contents