Snapper GT600 manual Mower Belt Replacement, Mower Drive Belt Replacement

Page 44

Troubleshooting, Adjustment, & Service

To avoid damaging belts, DO NOT PRY

BELTS OVER PULLEYS.

Mower Belt Replacement

Mower Drive Belt Replacement

1.Remove the mower deck. See Mower Removal and Installation

2.Remove the screws securing the belt covers and remove the belt covers.

3.Using a spring puller or a small rope loop, release the idler assembly tension spring (B, Figure 49).

4.Remove the old drive belt (D).

5.Inspect all pulleys for wear or bearing damage.

6.Lubricate the idler arm pivot with multi-purpose lithi- um grease and check for free movement.

7.Install the new drive belt as shown in the diagram in Figure 48.

8.Reinstall the belt covers. Be sure the alignment notches are centered on the screws.

9.Install the mower deck and run under no-load for five minutes to break in the new belt.

BELT ROUTING VIEWED FROM TOP

Outer

Outer

Pulley

Pulley

 

Drive

 

Pulley

V Idler

Belt

 

 

Double V

Center

 

Pulley

 

FRONT

 

Figure 48. Mower Belt Routing

A

C

 

A

B

D

A

 

Figure 49. Mower Deck - Covers Removed

A.Arbor Pulleys

B.Idler Arm Tension Spring

C.V-Idler Pulley

D.Drive Belt

42

Image 44
Contents OPERATOR’S Manual 27HP Hydro Tractors & Mower DecksPage Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineIdentification Numbers Tractor ID TagSafety Decals Safety DecalsDecal Danger Rotating Blades Decal Danger, Rotating Fan, Diesel Models Part NoSafety Icons Operational Safety ChecksControl Functions Features & Controls Parking Brake Function Automatic Controlled TractionDashboard Display Functions General Operating Safety Slope OperationAdding Fuel Stopping The Tractor & EngineOperating the Tractor Using Inboard Hydraulics Pushing The Tractor By HandHydraulic System Functions GeneralUsing Auxiliary Hydraulics Auxiliary Hydraulics Angle Left Angle RightLocking The Hitch Attachment Weight LimitOptional 3-Point Hitch Operation Select Models Hitch Arms Installation Connecting a Drive Shaft Rear PTO Operation Select ModelsChecks Before Starting Starting & Stopping the PTOAttachment Recommendations Mower Deck Removal & Installation Removing the Mower DeckInstalling the Mower Deck Mower Electrical ConnectionStorage Volt Power OutletAttaching a Trailer Regular Maintenance Before Every Spring Each Hours Fall UseRegular Maintenance Clean RadiatorClean Transmission Oil Cooler Check Engine Coolant LevelService Interval Seasonally or as Needed Drain Fuel SeparatorService Interval Every 25 Hours Check Transmission Oil LevelOil Filter Part No Change Transmission Oil & filterCheck Front Axle Oil Level Safety Interlock System Check Service Interval Every Fall & SpringService Interval Every 100 Hours or Fall & Spring Check Mower Deck Gear Box OilBattery Maintenance Cleaning the Battery and CablesCheck Tire Pressures Size TreadOil LubricationGrease Grease the Electric Lift Rod GreaseFitting Yearly Arm Grease Fitting YearlyServicing The Mower Blades Removing the BladeMaintenance Records Troubleshooting Adjustment, & Service Troubleshooting the Mower Troubleshooting, Adjustment, & Service Seat AdjustmentBrake Adjustment Seat Slide AdjustmentBattery Charging Headlight ReplacementTaillight & Dash Light Replacement Mower Adjustments Gauge Wheel AdjustmentSide-to-Side Adjustment Lock Nut, 5/16-18 Spacer Bolt Leveling The MowerTo avoid damaging belts, do not PRY Mower Belt ReplacementMower Drive Belt Replacement Specifications 27 HP* Briggs & StrattonReplacement Parts Maintenance ItemsOptional Accessories Technical ManualsPage Lawn Care Lawn Care & Mowing Information Page