Snapper EP217019BV important safety instructions On Next Replacing Rubber Driven Disc

Page 16

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.3.DRIVEN DISC ADJUSTMENT (Continued From Previous Page)

2.Remove driven disc spring from driven disc assembly. Also remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

DRIVEN DISC

ASSEMBLY

DRIVE

DISC

REMOVE

DRIVEN DISC

SPRING

REMOVE END

REMOVE

OF TRANSFER

ROD FROM

PIN AND

DRIVEN DISC

WASHER

ASSY

FROM ROD

FIGURE 4.9

3.Slide driven disc assembly over to 1/8” from outside edge of drive disc. See Figure 4.10.

4.Loosen jam nut securing transfer rod to ball joint on pivot bracket. See Figure 4.11.

5.Turn rod in or out of ball joint until end of rod aligns with hole in driven disc assembly from which rod was removed. NOTE: Do not move pivot bracket.

6.Reinstall rod as removed in step 2. Move ground speed control to ‘slow’ position, then back to ‘fast’ position. Recheck the 1/8” measurement described previously. Readjust as needed. Tighten nut when finished.

7.Reinstall driven disc spring to driven disc assembly.

1/8” MEASUREMENT TO OUTSIDE EDGE OF DRIVE DISC

DRIVE

SLIDE DRIVENDISC DISC ASSEMBLY

TOWARD OUTSIDE EDGE

OUTSIDE

EDGE

FIGURE 4.10

BALL JOINT

LOOSEN NUT

 

TURN ROD IN

PIVOT

OR OUT UNTIL

BRACKET

END ALIGNS

 

WITH HOLE

FIGURE 4.11

(Continued On Next Page)

4.3.4. Replacing Rubber Driven Disc

If the rubber is badly chunked or worn it must be replaced. Install new Driven Disc as follows:

1.Remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Engine Designation Series Designation Engine Horse Power European 21 Steel Deck Walk Mowers SeriesImportant Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Introduction Engine Speed ControlNomenclature PRE-START Check List Starting & Operation Engine & BladeCutting Height Adjustment Handle Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Dispose of drain oil properly Service After First 5 Hours 3.2.1. Change Engine OILImportant Drain fuel tank before tipping mower Service Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltBlade Sharpening Mower Blade Replacement Standard Blade Wear Limit1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments Engine Drive Belt Replacement Stretch Type Belts Belt ServiceOn Next Reinstall blade hub and cutter blade Pulley PositionProblem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT Parts100 USE HRS SeasonDecal Identification CE Compliance Specifications Year Limited Warranty Disclaimer of WarrantyPage Page Page European Steel Deck Walk Mowers Series

EP217019BV specifications

The Snapper EP217019BV is a versatile and robust electric lawn mower that combines power and convenience to deliver an exceptional mowing experience. Designed for residential use, this mower is perfect for homeowners looking to maintain their lawns with ease and efficiency.

One of the standout features of the Snapper EP217019BV is its powerful 48V lithium-ion battery system. This battery provides ample power to tackle even the toughest grass while delivering a significant runtime, allowing users to mow larger lawns without the need for frequent recharging. The battery’s quick-charge capability means less downtime, ensuring efficiency and convenience for users.

The 21-inch cutting deck made of high-strength steel ensures durability and longevity, allowing the mower to withstand the rigors of regular use. The cutting deck is not only strong but also lightweight enough to maneuver easily around obstacles in your yard. Moreover, it features a 3-in-1 cutting system that allows users to mulch, bag, or side discharge grass clippings, providing flexibility based on personal preference and lawn conditions.

Another notable characteristic of the Snapper EP217019BV is its adjustable cutting heights, which can be set between 1 to 4 inches. This range enables users to customize their cut for different types of grass and seasonal conditions, achieving the desired appearance for their lawn. The single-lever height adjustment makes switching between different height settings a breeze.

The mower is equipped with an ergonomic handle, designed for comfort during extended mowing sessions. It is also foldable, allowing for easy storage in compact spaces, a practical feature for users with limited storage options.

In terms of technology, the Snapper EP217019BV incorporates advanced brushless motor technology that enhances efficiency and performance while reducing maintenance needs. The brushless motor not only increases battery life but also offers quiet operation, making it suitable for use in residential areas without disturbing neighbors.

Overall, the Snapper EP217019BV stands out as a reliable electric lawn mower, marrying powerful performance with user-friendly features. With its efficient battery system, durable cutting deck, adjustable heights, and advanced technologies, this mower is an excellent choice for anyone looking to maintain a beautiful lawn.
Top Page Image Contents