Snapper EP217019BV Pulley Position, Reinstall blade hub and cutter blade

Page 19

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.4.1.Engine Drive Belt Replacement (Stretch Type Belts)

(Continued From Previous Page)

IMPORTANT: Drain fuel tank before tipping mower. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.

Remove the driven disc. Refer to Section

“Replacing Rubber Driven Disc” for driven disc

removal procedure.

4.

Drain fuel tank before tipping mower. Do not tilt

mower with spark plug or carburetor down. Tilt

mower up on its rear wheels and remove blade and

blade hub. Assistance from another person may be

necessary to hold mower in the tilted position.

5.

Hold the slotted end of the drive disc bolt with a

screwdriver and remove the nut and internal tooth

lock washer. See Figure 4.16.

6.

Remove the belt cover located under deck.

7.

Lift the drive disc up and remove worn belt.

8.

Loop one end of new belt over engine pulley and

insert the other end through slot in deck. Refer to

Figure 4.15.

PULLEY POSITION

DRIVE DISC

SLOT IN END

OF DRIVE DISC BOLT

BUSHING

DECK BRACKET

(PARTIALLY SHOWN)

BOLT RETAINER

INTERNAL TOOTH

LOCKWASHER

NUT

FIGURE 4.16

4.4.2.Transmission Poly-V Belt Replacement 1. Remove the driven disc. Refer to Section on “Replacing Driven Disc Rubber Ring” for procedure. 2. Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

3. Place new Poly-V Belt over end of hex shaft and onto drive pulley.

4. Work belt onto top of idler pulley.

5. Twist belt sideways and pull it upward between the differential bracket and driven pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

9. Loop the belt around the pulley on the bottom of

the drive disc.

10. Reinstall drive disc and retaining hardware.

DRIVE

IDLER

PULLEY DIFFERENTIAL BRACKET

IMPORTANT: 1) The square shoulder of the drive

disc bolt must fit into the square hole of the bushing.

2) The square end of bushing must fit into the

bracket slot.

11. Reinstall belt cover and tighten bolts securely.

12. Reinstall blade hub and cutter blade.

Recommended torque for blade cap screw is 40 ft. lbs.

PULLEYPOLY-V BELT

HEX SHAFT

BELT GUIDE

DRIVEN

 

PULLEY

 

ROUTING OF POLY-V BELT

 

FIGURE 4.17

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents European 21 Steel Deck Walk Mowers Series Engine Designation Series Designation Engine Horse PowerFrom Previous Column Important Safety InstructionsDo not refuel the machine indoors From PreviousImportant Safety Instructions Table of Contents Introduction Engine Speed ControlNomenclature Starting & Operation Engine & Blade PRE-START Check ListStopping Cutting Height AdjustmentHandle Height Adjustment Propelling MowerInstallation of Grass BAG Door Type Bag Recycling Operation Dispose of drain oil properly Service After First 5 Hours 3.2.1. Change Engine OILImportant Drain fuel tank before tipping mower Check Engine Drive Belt Service AnnuallyStorage Procedure Check Mower BladeBlade Sharpening Mower Blade Replacement Standard Blade Wear Limit1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven Disc Adjustment Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementOn Next Replacing Rubber Driven Disc Repair & Adjustments Engine Drive Belt Replacement Stretch Type Belts Belt ServiceOn Next Pulley Position Reinstall blade hub and cutter bladeCorrective Action Problem Probable CauseUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Decal Identification CE Compliance Specifications Disclaimer of Warranty Year Limited WarrantyPage Page Page European Steel Deck Walk Mowers Series

EP217019BV specifications

The Snapper EP217019BV is a versatile and robust electric lawn mower that combines power and convenience to deliver an exceptional mowing experience. Designed for residential use, this mower is perfect for homeowners looking to maintain their lawns with ease and efficiency.

One of the standout features of the Snapper EP217019BV is its powerful 48V lithium-ion battery system. This battery provides ample power to tackle even the toughest grass while delivering a significant runtime, allowing users to mow larger lawns without the need for frequent recharging. The battery’s quick-charge capability means less downtime, ensuring efficiency and convenience for users.

The 21-inch cutting deck made of high-strength steel ensures durability and longevity, allowing the mower to withstand the rigors of regular use. The cutting deck is not only strong but also lightweight enough to maneuver easily around obstacles in your yard. Moreover, it features a 3-in-1 cutting system that allows users to mulch, bag, or side discharge grass clippings, providing flexibility based on personal preference and lawn conditions.

Another notable characteristic of the Snapper EP217019BV is its adjustable cutting heights, which can be set between 1 to 4 inches. This range enables users to customize their cut for different types of grass and seasonal conditions, achieving the desired appearance for their lawn. The single-lever height adjustment makes switching between different height settings a breeze.

The mower is equipped with an ergonomic handle, designed for comfort during extended mowing sessions. It is also foldable, allowing for easy storage in compact spaces, a practical feature for users with limited storage options.

In terms of technology, the Snapper EP217019BV incorporates advanced brushless motor technology that enhances efficiency and performance while reducing maintenance needs. The brushless motor not only increases battery life but also offers quiet operation, making it suitable for use in residential areas without disturbing neighbors.

Overall, the Snapper EP217019BV stands out as a reliable electric lawn mower, marrying powerful performance with user-friendly features. With its efficient battery system, durable cutting deck, adjustable heights, and advanced technologies, this mower is an excellent choice for anyone looking to maintain a beautiful lawn.
Top Page Image Contents