Snapper HZT21481BV Important Safety Instructions, Towing, Maintenance

Page 4
TOWING

!

IMPORTANT SAFETY INSTRUCTIONS

!

TOWING

1.Tow only with a machine that has a hitch designed for towing. DO NOT attach towed equipment except at the hitch point.

2.Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes.

3.DO NOT allow children or others on towed equipment.

4.On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

5.Travel slowly and allow extra distance to stop.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of chil- dren in a well ventilated, unoccupied building.

2.Keep engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved con- tainer outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

MAINTENANCE

(Continued From Previous Column)

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect negative (black) cable from battery before performing maintenance or service. Cranking engine could cause injury.

8.DO NOT work under machine without safety blocks.

9.Service engine and make adjustments only when engine is stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or over- speed engine.

11.Lubricate machine at intervals specified in manual to pre- vent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when han- dling them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Have machine serviced by an authorized SNAPPER deal- er at least once a year and have the dealer install any new safety devices.

15.Maintain or replace safety and instruction labels as nec- essary.

16.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

!

WARNING

!

Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during nor- mal usage. Check condition of bags before each use. Immediately replace worn or damaged catcher bags with only bags recom- mended by SNAPPER. The Grass Catcher is optional equipment on some models.

4

Image 4
Contents MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES Safety Instructions & Operators Manual forMODELS HZT21481BVIMPORTANT SAFETY INSTRUCTIONS PROTECTION FOR CHILDRENPROTECTION AGAINST TIPOVERS PREPARATIONSAFE HANDLING OF GASOLINE OPERATIONMAINTENANCE TOWINGTABLE OF CONTENTS 1.1 INTRODUCTION Section 1 - FAMILIARIZATION1.2 NOMENCLATURE Section 2 - SAFETY MESSAGES AND SYMBOLS CATCHER MUST BE INSTALLED WEAR HEARING PROTECTIONDANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTSIGNITION SWITCH CONTROL PANEL IDENTIFICATIONDANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREASection 3 - OPERATING INSTRUCTIONS 3.1PRE-STARTCHECK LIST3.2.1. STARTING ENGINE 3.2.2. STOPPING ENGINE 3.4 OPERATION- MOTION CONTROLS 3.3CUTTING HEIGHT ADJUSTMENT3.4.1. DRIVING MACHINE 3.4.2. STOPPING MACHINE Section 4 - MAINTENANCE 4.2SERVICE - AFTER FIRST 5 HOURS4.1INTRODUCTION 4.2.2. CHECK MOWER BLADE4.3.2.MOWER COMPONENTS 1. Mower Drive Belt 4.3AFTER EVERY 25 OPERATING HOURS 4.3.1. ENGINEFIGURE Deck shown with discharge raised 4.4BEFORE OPERATING MACHINE 4.5ANNUALLY END OF EACH SEASON4.5.1. ENGINE FIGURE Continued on next Page4.6DECK REMOVAL Continued On Next PageSection 4 - MAINTENANCE 5.1NEUTRAL POSITION ADJUSTMENTS Section 5 - ADJUSTMENTS & REPAIRFIGURE Continued On Next Page 5.2 MOWER DECK & COMPONENT ADJUSTMENTS 5.2.1. MOWER DECK ADJUSTMENT LEVELNESSSIDE to SIDE and FRONT to REAR FIGURE FIGURE5.3PARKING BRAKE ADJUSTMENT FIGURE 5.6TRACKING ADJUSTMENT 5.4TRACTION BELT REPLACEMENT5.3 TRACTION BELT TENSION 5.7.2. BELT REPLACEMENT 5.8ENGINE ADJUSTMENTS & REPAIR 5.9.2. BLADE SHARPENING5.10BATTERY 5.10.1. BATTERY REMOVAL Battery Condition Chart 5.11HYDRAULIC SYSTEM, PURGING TROUBLESHOOTING PROBLEMPROBABLE CAUSE CORRECTIVE ACTIONBattery Will Not Charge Machine Will Not MoveLoss Of Traction Blades Not CuttingSERVICE SCHEDULE MAINTENANCE/REPLACEMENT PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atPage Page Page Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone MANUAL No. 700079 I.R. 5/27/2005