Snapper LT150H38GKV Blade Belt Adjustment 33 Deck, Blade Belt Adjustment 38 Deck, On next

Page 18

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. If deck front to rear level is not correct, this could cause blade belt problems.

4.2.2.BLADE BELT ADJUSTMENT – 33” DECK

1.Move tractor to a firm, level surface.

2.Turn engine "OFF". Remove key.

3.Move blade engagement lever down to "OFF". See Figure 4.2.

4.Place deck in mid cutting position.

5.Check front to rear level. Refer to Section “33 DECK LEVEL ADJUSTMENT (FRONT TO REAR)”.

MOVE BLADE

ENGAGEMENT

LEVER TO “OFF”

FIGURE 4.2

IMPORTANT: If deck front to rear level is not correct, this could cause blade belt problems.

6.Move blade engagement lever to "ON".

7.Measure blade cable extension spring. The length of the spring (x) should increase by 1” (+/-1/8”). See Figure

BLADE CABLE

EXTENSION

SPRING

X

X + 1” +/- 1/8”

8.(33" Deck) To adjust tension, remove extension rod mounting bolt and nut. See Figure 4.4.

9.Move extension rod to next hole towards rear of deck and secure with mounting bolt and nut.

10.Measure extension spring with blade engagement lever in the "ON" and "OFF" positions. See Figure 4.3. Continue adjustment until tension is correct.

IMPORTANT: Blade brake function must be verified after performing blade belt adjustment.

11.Check blade brake. Refer to Section “CHECK BLADE BRAKE”. Blades must stop rotating in 5 seconds or less when turned off.

LEAST TENSION

MOST TENSION

EXTENSION

ROD

MOUNTING

NUT & BOLT

FIGURE 4.4

4.2.3.BLADE BELT ADJUSTMENT – 38” DECK

The blade belt on the 38” deck requires no tension adjustment. If the belt becomes worn or damaged it must be replaced. Refer to Section “BLADE BELT REMOVAL &

REPLACEMENT”.

4.2.4.ADJUSTING MOWER BLADE – 33” DECK (33" Decks Only; no adjustment for 38")

1.Select a point on the deck and mark for reference.

2.Mark blade tips as “A” and “B”.

3.Rotate blade until blade tip “A” is at deck reference mark

4.Measure the distance between deck lip and blade tip. Note the measurement. See Figure 4.5.

(Continued on next page)

FIGURE 4.3

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lawn Tractor Hydrostatic Drive Series G Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting & Operation 2.3.2. Starting Wheel Drive Starting Mower BladeStopping Wheel Drive Stopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterService Annually 3.4.2. Fuel Filter From PreviousSpark Plug Hydrostatic Transmission OIL Engine Adjustments & Repair Blade Brake AdjustmentDeck Blade Brake Adjustment Blade Belt Adjustment 33 Deck Blade Belt Adjustment 38 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Side to Side Deck Level Adjustment Front to Rear Sector PlatesDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Deck Level Adjustment Front to Rear Tractor Drive Components 4.3.1. Brake AdjustmentRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Schematic Wiring Harness P.N Schematic Wiring Harness P.N LT150HG38KVLT145H33GBV & LT145H38GBV Troubleshooting Guide Troubleshooting Guide LT145H33GBV Tractor Drive Belts Mower BladesNinja LT145H38GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

WLT145H38GBV, LT150H38GKV, LT145H38GBV specifications

The Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV are robust lawn tractors designed to provide efficient and reliable performance for homeowners and landscaping professionals alike. Each model offers a unique combination of features and technologies that enhance usability, comfort, and mowing precision.

The Snapper LT145H38GBV is powered by a 14.5 horsepower Briggs & Stratton engine, providing ample power for tackling various mowing tasks. It features a 38-inch cutting deck, made of durable steel, which allows for an optimal cutting width, making the mowing process quicker and more efficient. The LT145H38GBV also incorporates a convenient foot pedal-operated hydrostatic transmission, allowing smooth acceleration and effortless speed control without any gear shifting.

Next, the Snapper LT150H38GKV stands out with its 15 horsepower Kohler engine. This model offers increased power, making it suitable for larger lawns or tougher grass conditions. Like the LT145, it boasts a 38-inch cutting deck, but the LT150H38GKV is also equipped with a high-back seat for added comfort during longer mowing sessions. Its sturdy construction ensures durability, while its easy-to-use dashboard controls provide a user-friendly experience.

Finally, the Snapper WLT145H38GBV offers similar features to the other models but adds versatility to the mix with its wider range of capabilities. This model is designed with a tight turning radius, making it easier to navigate around flower beds and trees. The WLT145H38GBV is also powered by a reliable 14.5 horsepower engine, ensuring efficient power delivery. Its cutting deck features multiple height-adjustment settings, allowing users to customize their mowing experience according to grass types and preferences.

All three models incorporate Snapper's innovative technologies, such as the easy-access under-deck washout port that simplifies the cleaning process and supports maintenance. They also come with a variety of cutting options, providing both side discharge and mulching capabilities, enhancing lawn health and appearance. With their user-friendly designs, ample power, and strong construction, the Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV represent an excellent choice for anyone seeking reliable lawn care solutions.
Top Page Image Contents