Snapper WLT145H38GBV, LT150H38GKV Steering Adjustment, Shifter Adjustment

Page 23

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.3.2.STEERING ADJUSTMENT

Should excessive “Play” be noted in the steering, adjust as follows:

1.Turn engine “OFF”. Remove key.

2.From left side of tractor, locate the steering sector below fuel tank. See Figure 4.19.

FUEL TANK

ROTATE TO

REDUCE “PLAY”

ECCENTRIC

MOUNTING NUT

FIGURE 4.19

3.Loosen the eccentric mounting nut and rotate the eccentric clockwise until steering “Play” is reduced. See Figure 4.19.

4.Tighten eccentric mounting nut.

4.3.3.SHIFTER ADJUSTMENT

The shift linkage is set at the factory and should not require further adjustment. The shifter is adjusted properly when the speed control lever can be placed at rear edge of the neutral detent and the tractor remains absolutely stationary. If motion is detected, neutral adjustment will be required. DO NOT operate a machine that creeps when shifted to neutral.

1.Stop engine. Remove key.

2.Move speed control lever to rear edge of neutral detent and hold firmly.

3.Locate neutral adjustment nut underneath the right rear of the tractor. See Figure 4.20

4.Turn the neutral adjustment nut 1/4 turn clockwise to reduce FORWARD creep. Turn the adjustment nut 1/4 turn counter clockwise to reduce Reverse creep. Only turn the adjustment nut in 1/4 turn increments.

5.Check for creep in neutral. Start engine. Move speed control lever to rear edge of the neutral detent. Machine should not move. If further adjustment is required, stop engine and repeat Step 4.

NEUTRAL

ADJUSTMENT

NUT

TURN NUT CLOCKWISE TO

REDUCE FORWARD CREEP

FIGURE 4.20

WARNING

DO NOT adjust shift linkage with engine running. The adjustment requires hands to be close to rotating parts. STOP engine. REMOVE key.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Number Explanation Lawn Tractor Hydrostatic Drive Series GImportant Safety Instructions Operation Table of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStopping Wheel Drive Starting & Operation 2.3.2. Starting Wheel DriveStarting Mower Blade Releasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILCheck 38 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 33 Deck Drive BeltTractor Lubrication Fuel Filter Service AnnuallySpark Plug Hydrostatic Transmission OIL Service Annually 3.4.2. Fuel FilterFrom Previous Deck Blade Brake Adjustment Engine Adjustments & RepairBlade Brake Adjustment On next Blade Belt Adjustment 33 DeckBlade Belt Adjustment 38 Deck Side View of Deck Adjusting Mower Blade 33 Deck from previousDeck Level Adjustment Front to Rear Front Lift ROD Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Sector Plates Front of Tractor Rear to Front View of Deck Deck Level Adjustment Front to RearTractor Drive Components 4.3.1. Brake Adjustment Shifter Adjustment Steering AdjustmentMounting Ninja Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Standard Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable Accessories LT145H33GBV & LT145H38GBV Schematic Wiring Harness P.NSchematic Wiring Harness P.N LT150HG38KV Troubleshooting Guide Troubleshooting Guide LT145H38GBV Tractor Drive Belts Mower BladesNinja LT145H33GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

WLT145H38GBV, LT150H38GKV, LT145H38GBV specifications

The Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV are robust lawn tractors designed to provide efficient and reliable performance for homeowners and landscaping professionals alike. Each model offers a unique combination of features and technologies that enhance usability, comfort, and mowing precision.

The Snapper LT145H38GBV is powered by a 14.5 horsepower Briggs & Stratton engine, providing ample power for tackling various mowing tasks. It features a 38-inch cutting deck, made of durable steel, which allows for an optimal cutting width, making the mowing process quicker and more efficient. The LT145H38GBV also incorporates a convenient foot pedal-operated hydrostatic transmission, allowing smooth acceleration and effortless speed control without any gear shifting.

Next, the Snapper LT150H38GKV stands out with its 15 horsepower Kohler engine. This model offers increased power, making it suitable for larger lawns or tougher grass conditions. Like the LT145, it boasts a 38-inch cutting deck, but the LT150H38GKV is also equipped with a high-back seat for added comfort during longer mowing sessions. Its sturdy construction ensures durability, while its easy-to-use dashboard controls provide a user-friendly experience.

Finally, the Snapper WLT145H38GBV offers similar features to the other models but adds versatility to the mix with its wider range of capabilities. This model is designed with a tight turning radius, making it easier to navigate around flower beds and trees. The WLT145H38GBV is also powered by a reliable 14.5 horsepower engine, ensuring efficient power delivery. Its cutting deck features multiple height-adjustment settings, allowing users to customize their mowing experience according to grass types and preferences.

All three models incorporate Snapper's innovative technologies, such as the easy-access under-deck washout port that simplifies the cleaning process and supports maintenance. They also come with a variety of cutting options, providing both side discharge and mulching capabilities, enhancing lawn health and appearance. With their user-friendly designs, ample power, and strong construction, the Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV represent an excellent choice for anyone seeking reliable lawn care solutions.
Top Page Image Contents