Snapper LT150H38GKV, WLT145H38GBV Battery Testing, NEW Battery Preparation

Page 31

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery.

4.5.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4.5.6NEW BATTERY PREPARATION

1.Remove battery from carton.

2.Place battery in a well ventilated area on a level non- concrete surface.

3.Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4.5.7. BATTERY TESTING

4.With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. However do not try to measure this dimension. Never place anything in battery other than specified electrolyte.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall seat assembly.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) cable must go to the ( - ) terminal.

Battery Condition Chart

 

State of Charge

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100%

Charged w/ Sulfate Stop

1.280

12.80v

Five Balls Floating

100%

Charged

1.265

12.60v

Four Balls Floating

75% Charged

1.210

12.40v

Three Balls Floating

50% Charged

1.160

12.10v

Two Balls Floating

25% Charged

1.120

11.90v

One Ball Floating

0% Charged

Less than 1.100

Less than 11.80v

Zero Balls Floating

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model Number Explanation Lawn Tractor Hydrostatic Drive Series GImportant Safety Instructions Operation Table of Contents Controls ComponentsOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistOFF Starting & Operation Starting EngineStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Releasing Park Brake Setting Park BrakeCutting Height Adjustment Stopping Stopping Mower BladeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismCheck Blade Brake Service After First 5 HoursIntroduction Change Engine OILCheck 38 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 33 Deck Drive BeltTractor Lubrication Fuel Filter Service AnnuallyFrom Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Side View of Deck Adjusting Mower Blade 33 Deck from previousDeck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Tractor Drive Components 4.3.1. Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Shifter Adjustment Steering AdjustmentMounting Ninja Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Standard Blade SharpeningTraction Drive Belt Replacement Mower Deck Removal Mower Blade ReplacementTraction drive belt removal View from Underneath Tractor Traction drive belt replacementDeck Drive Belt Battery Storage Battery Battery RemovalBattery Installation Battery ServiceNEW Battery Preparation Battery TestingAvailable Accessories Schematic Wiring Harness P.N LT150HG38KV Schematic Wiring Harness P.NLT145H33GBV & LT145H38GBV Troubleshooting Guide Troubleshooting Guide LT145H38GBV Tractor Drive Belts Mower BladesNinja LT145H33GBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series G

WLT145H38GBV, LT150H38GKV, LT145H38GBV specifications

The Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV are robust lawn tractors designed to provide efficient and reliable performance for homeowners and landscaping professionals alike. Each model offers a unique combination of features and technologies that enhance usability, comfort, and mowing precision.

The Snapper LT145H38GBV is powered by a 14.5 horsepower Briggs & Stratton engine, providing ample power for tackling various mowing tasks. It features a 38-inch cutting deck, made of durable steel, which allows for an optimal cutting width, making the mowing process quicker and more efficient. The LT145H38GBV also incorporates a convenient foot pedal-operated hydrostatic transmission, allowing smooth acceleration and effortless speed control without any gear shifting.

Next, the Snapper LT150H38GKV stands out with its 15 horsepower Kohler engine. This model offers increased power, making it suitable for larger lawns or tougher grass conditions. Like the LT145, it boasts a 38-inch cutting deck, but the LT150H38GKV is also equipped with a high-back seat for added comfort during longer mowing sessions. Its sturdy construction ensures durability, while its easy-to-use dashboard controls provide a user-friendly experience.

Finally, the Snapper WLT145H38GBV offers similar features to the other models but adds versatility to the mix with its wider range of capabilities. This model is designed with a tight turning radius, making it easier to navigate around flower beds and trees. The WLT145H38GBV is also powered by a reliable 14.5 horsepower engine, ensuring efficient power delivery. Its cutting deck features multiple height-adjustment settings, allowing users to customize their mowing experience according to grass types and preferences.

All three models incorporate Snapper's innovative technologies, such as the easy-access under-deck washout port that simplifies the cleaning process and supports maintenance. They also come with a variety of cutting options, providing both side discharge and mulching capabilities, enhancing lawn health and appearance. With their user-friendly designs, ample power, and strong construction, the Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV represent an excellent choice for anyone seeking reliable lawn care solutions.
Top Page Image Contents