Snapper LT145H33HBV, LT145H38HBV, LT150H38HKV, WLT145H38HBV Deck Level Adjustment Front to Rear

Page 22

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.38" DECK LEVEL ADJUSTMENT (FRONT TO REAR)

1.Position the blades as shown. See Figure 4.16.

FRONT OF TRACTOR

LEFT FRONT

BLADE TIP

RIGHT REAR BLADE TIP

FIGURE 4.16

2.Measure the distance from the left front blade tip to the ground and from the right rear blade tip to the ground. The front left blade tip should be between 1/8" and 3/8" higher than the right rear (factory setting). If it is between 1/8" and 3/8" you are finished with adjustment.

3.If it is not within specifications, adjust by raising or lowering the front of the deck using the swivel on the front lift rod. Turning the swivel clockwise will raise the front of the deck. Turning the swivel counterclockwise will lower the front of the deck.

NOTE: The deck should be set so that the rear of the deck is 1/4" lower than the front. See Figure 4.17.

REAR TO FRONT VIEW OF DECK

 

X

X - 1/8”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANGLE IRON

FIGURE 4.17

4.3 TRACTOR DRIVE COMPONENTS

4.3.1.BRAKE ADJUSTMENT

When adjusted properly, the brake should stop the tractor in approximately 6 feet or less from top speed. Drive the machine at maximum forward speed and apply the brake. If stopping distance is greater than 6 feet, brake adjustment is required.

1.Turn engine “OFF”. Remove key.

2.Locate brake adjustment nut underneath the left side at the rear of tractor. See Figure 4.18.

3.Turn nut 1 turn clockwise to increase braking action. DO NOT over tighten brake adjustment.

4.Start engine and test brake.

5.Continue adjustment as described above until proper brake function is achieved.

ROTATE ADJUSTING NUT CLOCKWISE TO

INCREASE BRAKING OR COUNTER

CLOCKWISE TO DECREASE BRAKING

FIGURE 4.18

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Lawn Tractor Hydrostatic Drive Series H Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components ControlsPRE-START Checklist OPERATOR’S Seat Adjustment Front to Rear AdjustmentStarting & Operation Starting Engine OFFStarting Mower Blade Starting & Operation 2.3.2. Starting Wheel DriveStopping Wheel Drive Stopping Stopping Mower Blade Setting Park BrakeCutting Height Adjustment Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideChange Engine OIL Service After First 5 HoursIntroduction Check Blade BrakeCheck 33 Deck Drive Belt Service Every 25 Operating HoursCheck Engine Check 38 Deck Drive BeltTractor Lubrication Service Annually Fuel FilterFrom Previous Service Annually 3.4.2. Fuel FilterSpark Plug Hydrostatic Transmission OIL Blade Brake Adjustment Engine Adjustments & RepairDeck Blade Brake Adjustment Blade Belt Adjustment 38 Deck Blade Belt Adjustment 33 DeckOn next Adjusting Mower Blade 33 Deck from previous Side View of DeckDeck Level Adjustment Front to Rear Sector Plates Deck Level Adjustment Side to SideDeck Level Adjustment Front to Rear Front Lift ROD Front of Tractor Tractor Drive Components Brake Adjustment Deck Level Adjustment Front to RearRear to Front View of Deck Steering Adjustment Shifter AdjustmentMounting Standard Blade Sharpening Mower Blade Service Standard Blade Wear LimitsNinja Blade Wear Limits Ninja Blade SharpeningMower Blade Replacement Traction Drive Belt Replacement Mower Deck RemovalTraction drive belt removal Traction drive belt replacement View from Underneath TractorDeck Drive Belt Battery Service Battery Battery RemovalBattery Installation Battery StorageBattery Testing NEW Battery PreparationAvailable Accessories Schematic Wiring Harness P.N LT150H38HKV Schematic Wiring Harness P.NLT145H33HBV & LT145H38HBV Troubleshooting Guide Troubleshooting Guide LT145H33HBV Tractor Drive Belts Mower BladesNinja LT145H38HBVYear Limited Warranty Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Lawn Tractor Hydrostatic Drive Series H

LT145H33HBV, LT145H38HBV, LT150H38HKV, WLT145H38HBV specifications

The Snapper LT145H33HBV, LT145H38HBV, LT150H38HKV, and WLT145H38HBV are versatile lawn tractors designed to deliver exceptional performance and efficiency for homeowners and professionals alike. Each model incorporates a host of features and technologies that enhance usability and mowing capabilities.

Starting with the LT145H33HBV, this model is equipped with a powerful Briggs & Stratton engine, providing reliable performance for handling various lawn care tasks. Its 33-inch cutting deck offers maneuverability, making it ideal for smaller to medium-sized yards. The LT145H33HBV also features an automatic transmission that allows for smooth and easy speed adjustments, promoting a more comfortable mowing experience. Its adjustable seat provides additional comfort during longer mowing sessions, and the sturdy construction ensures durability and longevity in outdoor conditions.

The LT145H38HBV model builds upon the foundation of the LT145H33HBV, but it comes with a larger 38-inch cutting deck, which is perfect for tackling larger lawns more efficiently. Like the LT145H33HBV, it features a reliable Briggs & Stratton engine, ensuring powerful performance. The LT145H38HBV is also equipped with Snapper’s proprietary Smart Speed technology, allowing users to easily switch between different speed settings, enabling precision control while navigating around obstacles.

On to the LT150H38HKV, this model offers even more power and features. With a robust 150cc engine and a 38-inch cutting width, it balances power and size perfectly. The LT150H38HKV also includes a high-back seat for enhanced comfort and support. Furthermore, this model integrates integrated mulching capabilities, letting users maintain their lawns effectively by returning valuable nutrients back to the soil. The easy-to-use cutting height adjustment system ensures users can achieve the desired grass length with minimal hassle.

Lastly, the WLT145H38HBV combines innovative technology with user-friendly design. This model stands out with its exceptional maneuverability due to its compact size. The 38-inch cutting deck expertly handles various terrains, making it a great choice for gardens with tight spaces. It incorporates a reinforced deck for added strength and longevity. Additionally, the WLT145H38HBV is designed with a comfortable steering wheel and ergonomic controls, ensuring that users can enjoy a seamless mowing experience.

In summary, Snapper's LT145H33HBV, LT145H38HBV, LT150H38HKV, and WLT145H38HBV models are not only equipped with powerful engines and durable cutting decks but also feature technologies that promote user comfort and cutting efficiency. With versatile options suitable for a range of lawn sizes, these tractors are designed to meet the needs of both casual users and serious lawn care enthusiasts.
Top Page Image Contents