Snapper RP2167517BVE Pulley Position, Transmission Poly-V Belt Replacement

Page 20

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or servicewith engine and blade running.STOP engine and blade.Disconnect spark plug wire and secure away from spark plug.Engine and components are HOT. Avoid serious burns, allow sufficienttime for allcomponents to cool.

4.4.1.Engine Drive Belt Replacement

(Stretch Type Belts)

(Continued From Previous Page)

IMPORTANT: Drain fuel tank before tipping mower. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be

replaced.

3.Remove the driven disc. Refer to Section

"Replacing Rubber Driven Disc" for driven disc assembly removal procedure.

4.Tilt mower up on its rear wheels and remove blade and blade hub. Assistance from another

person may be necessary to hold mower in the tilted position.

5.Hold the slotted end of the drive disc bolt with a screwdriver and remove the nut and internal tooth

lock washer. See Figure 4.16.

6.

Remove the belt cover located under deck.

7.

Lift the drive disc up and remove

worn

belt.

8.

Loop one

end of new belt over engine pulley and

insert the

other

end

through

slot

in deck.

See Figure 4.15.

 

 

 

 

9.

Loop the belt around the pulley on the bottom of

the drive disc.

 

 

 

 

10. Reinstall

drive

disc and

retaining

hardware.

PULLEY POSITION

DRIVE DISC

SLOT IN END

OF DRIVE DISC

BOLT

BUSHING

DECK BRACKET

(PARTIALLY SHOWN)-"_

_

BOLT RETAINER

_-_ _?>_NuTLOCK WASHER

I

FIGURE 4.16

4.4.2.Transmission Poly-V Belt Replacement

1.Remove the driven disc. Refer to Section on

"Replacing Driven Disc Rubber Ring" for procedure.

2.Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

3.Place new Poly-V Belt over end of hex shaft and onto driven pulley.

4.Work belt onto top of idler pulley.

5.Twist belt sideways and pull it upward between the differential bracket and drive pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

IDLER

IMPORTANT: 1) The square shoulder of the drive

disc bolt must fit into the square hole of the bushing.

2)The square end of bushing must fit into the bracket slot.

DRIVE PULLEY

BRACKET

11.Reinstall belt cover and tighten bolts securely.

12.Reinstall blade hub and cutter blade.

Recommended torque for blade cap screw is 40 ft. Ibs.

HEX SHAFT

BELT GUIDE

DRIVEN

 

PULLEY

ROUTING OF POLY-V BELT

FIGURE 4.17

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Engine Designation Series Designation Engine Horse Power 8NAPPERo McDonough, GA., 30253 U.S.AImportant Safety Instructions Operation Table of Contents Briggs EngineSpeed ControlPrimer Models PRE-START Check ListStarting & Operation Engine & Blade Stopping Starting & Operation 2.2.1. Engine & BladePropelling Mower Handle Height Adjustment Cutting Height AdjustmentRecycling Operation On NextInstallation of Grass Catcher Slide Closure Type Removing and Dumping Grass CatcherComponents immediately Important Drain fuel tank before tipping machine Service After First 5 Hours 3.2.1. Change Engine OILIntroduction Service -ANNUALLY Storage ProcedureImportant Drain fuel tank before tipping mower. do Check Mower BladeMower Blade Replacement Standard Blade Wear LimitBlade Sharpening 1.A. Ninja Blade Wear LimitWheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentReplacing Rubber Driven Disc Repair & Adjustments Engine Drive Belt Replacement Stretch Type Belts Replacement Of Bearing On Pulley End Hex ShaftBelt Service Important 1 The square shoulder of the drive Transmission Poly-V Belt ReplacementPulley Position Battery Service NEW Battery Preparation Battery StorageBattery Testing Syringe Hydrometer Digital VoltmeterTroubleshooting HRS HRS HRS Season Service Performed Each USE HRSMAINTENANCE/REPLACEMENT Parts Year Limited Warranty Disclaimer of WarrantyVs.DIRT Cost YOU Money That dirt willCheck OIL Level Before Each START-UP Starting Check UST Spark plugSnapper Product Registration Form Page Page Page Steel Deck Walk Behind Mowers Series Snapper McDonough, GA., 30253 U.S.A

RP2167517BVE specifications

The Snapper RP2167517BVE is a versatile and powerful riding mower, engineered for homeowners seeking efficiency and comfort in lawn care. Designed with a 21 horsepower Briggs & Stratton engine, this mower provides more than just power; it boasts exceptional reliability, ensuring a consistent performance on various terrains. One of its standout features is the professional-grade, 42-inch dual-blade cutting deck, which allows for precise cutting and an impressive turnaround radius that enhances maneuverability around your yard.

Equipped with a unique hydrostatic transmission, the RP2167517BVE offers seamless speed control and smooth handling, allowing users to easily navigate tricky landscapes. The foot-operated automatic transmission provides the rider with the ability to accelerate or decelerate without the complexity of manual shifting. This means that mowing becomes less of a chore and more of an enjoyable task, even in larger properties.

Comfort is a major highlight of the Snapper RP2167517BVE. It comes with an adjustable high-back seat designed to reduce fatigue during extended mowing sessions. The position is customizable to suit different user preferences, allowing for an ergonomic driving experience. Furthermore, the intuitive control panel places essential functions within easy reach, making it straightforward to operate.

In addition to these features, the RP2167517BVE is compatible with various attachments, including baggers, mulchers, and snow blades, making it a multi-season workhorse for lawn and garden maintenance. The sturdy build of the mower is complemented by robust safety features, such as an automatic engine shut-off when the operator leaves the seat.

Another technological advantage of the Snapper RP2167517BVE is its tough construction, featuring a welded steel frame that stands up to rigorous use. The mower is also designed for easy maintenance, with access points that allow for quick cleaning of the deck and adjustments.

Overall, the Snapper RP2167517BVE combines power, comfort, and advanced technology to provide a superior mowing experience. Whether tending to a sprawling lawn or navigating tight spaces, this riding mower delivers performance and reliability that meet the demands of any homeowner.
Top Page Image Contents