Snapper P2167519B, P217019BVE, P216019KWV From Previous, On Next Replacing Rubber Driven Disc

Page 17

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or servicewith engine and blade running.STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are

1/8" MEASUREMENT TO OUTSIDE EDGE OF DRIVE

DISC

HOT. Avoid serious burns, allow sufficienttime for

SLIDE DRIVEN

DRIVE DISC

allcomponents to cool.

4.3.3.DRIVEN DISC ADJUSTMENT

(Continued From Previous Page)

DISC ASSEMBLY TOWARD OUTSIDE

EDGE

2.Remove driven disc spring from driven disc assembly. Also remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

DRIVEN DISC

ASSEMBLY

DRIVE

DISC

REMOVE

DRIVEN DISC

SPRING

REMOVE

EN

 

OF TRANSFER

REMOVE

ROD FROM

PIN AND

DRIVEN

DISC

WASHER

ASSY

 

FROM ROD

FIGURE 4.9

3.Slide driven disc assembly over to 1/8" from outside edge of drive disc. See Figure 4.10.

4.Loosen jam nut securing transfer rod to ball joint on pivot bracket. See Figure 4.11.

5.Turn rod in or out of ball joint until end of rod aligns with hole in driven disc assembly from which rod was removed. NOTE: Do not move pivot bracket.

6.Reinstall rod as removed in step 2. Move ground speed control to 'slow'position, then back to 'fast' position. Recheck the 1/8" measurement described previously. Readjust as needed. Tighten nut when finished.

7.Reinstall driven disc spring to driven disc assembly.

OUTSIDE

EDGE

FIGURE 4.10

BALL JOINT

LOOSEN NUT

" I

U

i

jl

TU!N ROD IN

 

PIVOT

BRACKET

WITH HOLE

FIGURE 4.11

(Continued On Next Page)

4.3.4.Replacing Rubber Driven Disc

If the rubber is badly chunked or worn it must be replaced. Install new Driven Disc as follows:

1.Remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc

assembly. See Figure 4.9.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model Number Explanation Steel Deck Walk Mowers SeriesImportant Safety Instructions Operation Usage Statement Table of Contents Introduction Nomenclature Briggs Engine Speed ControlKawasaki Engine Speed Control Engine & Blade Briggs Engine PRE-START Check ListStarting & Operation Cutting Height Adjustment Handle Height AdjustmentPropelling Mower Stopping10a Installation of Grass BAG AdapterRemoving and Dumping Grass Catcher Slide Closure Type Installation of Grass CatcherRecycling Operation Check Grease Level in Transmission Service After First 5 Hours 3.2.1. Change Engine OILIntroduction SERVICE-ANNUALLY Storage ProcedureInjury Check Mower BladeMower Blade Replacement Standard Blade Wear Limit Repair & AdjustmentsWheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc From PreviousInstall NEW Driven Disc Remove Belt Service Replacement Of Bearing On Pulley End Hex ShaftEngine Drive Belt Replacement Stretch Type Belts On NextPulley Position Transmission Poly-V Belt ReplacementBattery Service Battery Service NEW Battery PreparationBattery Testing Syringe Hydrometer Digital VoltmeterCorrective Action TroubleshootingHRS HRS HRS Season Service Performed Each USE HRSMAINTENANCE/REPLACEMENT Parts Disclaimer of Warranty Year Limited WarrantyIllustration Engine & how Can protect Itv Result In hard starting Create smoke from unburn PmduPrimary Maintenance Starting Check UST Snapper Product Registration Form Page Page GA., 30253 U.S,A Steel Deck Walk Behind Mowers Series

P216019KWV, P217019BV, P2167519B, P217019BVE specifications

The Snapper P217019BVE, P216019KWV, P217019BV, and P2167519B are a selection of high-performance lawn mowers designed to meet the needs of both residential and commercial users. These models are characterized by their durability, innovative features, and user-friendly designs, making them suitable for a variety of lawn care tasks.

One of the key features of these Snapper mowers is their powerful Briggs & Stratton engines. These engines are known for their reliability and efficient performance, providing ample power to tackle tough grass conditions. The P217019BVE and P217019BV feature a self-propelled drive system, allowing users to navigate uneven terrain with ease. This attribute significantly reduces the physical effort required by the operator, making lawn maintenance less of a chore.

The cutting deck design is another highlight of these models. Snapper has engineered these mowers with a 21-inch steel cutting deck that ensures a clean and precise cut. Additionally, users can easily adjust the cutting height, allowing for customization based on grass types and desired lawn aesthetics. The mulching capability enhances versatility, enabling users to recycle grass clippings back into the lawn for added nutrients.

The Snapper P216019KWV, with its innovative technology, boasts an electric start feature, eliminating the hassle of pull-starting. This convenience is particularly appreciated by those who may struggle with traditional starting methods. Furthermore, all models are designed with easy-to-use controls, ensuring a comfortable mowing experience for users of all skill levels.

Durability is another essential characteristic of Snapper mowers. With rust-resistant materials and reinforced construction, these machines are built to withstand the rigors of frequent use. The P2167519B also features large rear wheels that enhance stability and maneuverability, making it easy to navigate through tight spaces or uneven landscapes.

In summary, the Snapper P217019BVE, P216019KWV, P217019BV, and P2167519B models stand out for their powerful engines, self-propelled systems, adjustable cutting decks, and user-friendly features. Designed for both performance and durability, these mowers are perfect for anyone looking to maintain a beautifully manicured lawn with ease and efficiency, providing excellent value in the realm of outdoor power equipment.
Top Page Image Contents