Snapper P217019BVE, P2167519B, P216019KWV Pulley Position, Transmission Poly-V Belt Replacement

Page 20

Section 4 - REPAIR & ADJUSTMENTS

WARNING

PULLEY POSITION

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

SLOT IN END OF DRIVE DISC BOLT

_DRIVE DISC

4.4.1.Engine Drive Belt Replacement (Stretch Type Belts)

(Continued From Previous Page)

DECK BRACKET

HING

IMPORTANT: Drain fuel tank before tipping mower. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the

engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be

replaced.

3.Remove the driven disc. Refer to Section "Replacing Rubber Driven Disc" for driven disc removal procedure.

4.Drain fuel tank before tipping mower. Do not tilt mower with spark plug or carburetor down. Tilt mower up on its rear wheels and remove blade and blade hub. Assistance from another person may be

necessary to hold mower in the tilted position.

5.Hold the slotted end of the drive disc bolt with a screwdriver and remove the nut and internal tooth

lock washer. See Figure 4.16.

6.

Remove the belt cover located under deck.

7.

Lift the drive

disc up and remove worn belt.

8.

Loop one end of new belt over

engine pulley and

insert the other

end through slot

in deck. Refer to

Figure 4.15.

 

 

(PARTIALLY SHOWN)

l

FIGURE 4.16

4.4.2.Transmission Poly-V Belt Replacement

1.Remove the driven disc. Refer to Section on "Replacing Driven Disc Rubber Ring" for procedure.

2.Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

3.Place new Poly-V Belt over end of hex shaft and onto drive pulley.

4.Work belt onto top of idler pulley.

5.Twist belt sideways and pull it upward between the differential bracket and driven pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

IDLER

9. Loop the belt around the pulley on the bottom of

the drive disc.

10. Reinstall drive disc and retaining hardware.

DRIVE

DIFFERENTIAL BRACKET

J

IMPORTANT: 1) The square shoulder of the drive disc bolt must fit into the square hole of the bushing.

2)The square end of bushing must fit into the bracket slot.

11.Reinstall belt cover and tighten bolts securely.

12.Reinstall blade hub and cutter blade.

Recommended torque for blade cap screw is 40 ft. Ibs.

PULLEY

BELT GUIDE

,DRIVEN

PULLEY

 

 

ROUTING OF POLY-V BELT

FIGURE 4.17

2O

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Steel Deck Walk Mowers Series Model Number ExplanationImportant Safety Instructions Operation Usage Statement Table of Contents Introduction Nomenclature Briggs Engine Speed ControlKawasaki Engine Speed Control Engine & Blade Briggs Engine PRE-START Check ListStarting & Operation Handle Height Adjustment Cutting Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Adapter 10aInstallation of Grass Catcher Removing and Dumping Grass Catcher Slide Closure TypeRecycling Operation Check Grease Level in Transmission Service After First 5 Hours 3.2.1. Change Engine OILIntroduction Storage Procedure SERVICE-ANNUALLYInjury Check Mower BladeRepair & Adjustments Mower Blade Replacement Standard Blade Wear LimitWheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentFrom Previous On Next Replacing Rubber Driven DiscInstall NEW Driven Disc Remove Replacement Of Bearing On Pulley End Hex Shaft Belt ServiceEngine Drive Belt Replacement Stretch Type Belts On NextTransmission Poly-V Belt Replacement Pulley PositionBattery Service NEW Battery Preparation Battery ServiceBattery Testing Syringe Hydrometer Digital VoltmeterTroubleshooting Corrective ActionHRS HRS HRS Season Service Performed Each USE HRSMAINTENANCE/REPLACEMENT Parts Year Limited Warranty Disclaimer of WarrantyIllustration Engine & how Can protect Itv Pmdu Result In hard starting Create smoke from unburnPrimary Maintenance Starting Check UST Snapper Product Registration Form Page Page Steel Deck Walk Behind Mowers Series GA., 30253 U.S,A

P216019KWV, P217019BV, P2167519B, P217019BVE specifications

The Snapper P217019BVE, P216019KWV, P217019BV, and P2167519B are a selection of high-performance lawn mowers designed to meet the needs of both residential and commercial users. These models are characterized by their durability, innovative features, and user-friendly designs, making them suitable for a variety of lawn care tasks.

One of the key features of these Snapper mowers is their powerful Briggs & Stratton engines. These engines are known for their reliability and efficient performance, providing ample power to tackle tough grass conditions. The P217019BVE and P217019BV feature a self-propelled drive system, allowing users to navigate uneven terrain with ease. This attribute significantly reduces the physical effort required by the operator, making lawn maintenance less of a chore.

The cutting deck design is another highlight of these models. Snapper has engineered these mowers with a 21-inch steel cutting deck that ensures a clean and precise cut. Additionally, users can easily adjust the cutting height, allowing for customization based on grass types and desired lawn aesthetics. The mulching capability enhances versatility, enabling users to recycle grass clippings back into the lawn for added nutrients.

The Snapper P216019KWV, with its innovative technology, boasts an electric start feature, eliminating the hassle of pull-starting. This convenience is particularly appreciated by those who may struggle with traditional starting methods. Furthermore, all models are designed with easy-to-use controls, ensuring a comfortable mowing experience for users of all skill levels.

Durability is another essential characteristic of Snapper mowers. With rust-resistant materials and reinforced construction, these machines are built to withstand the rigors of frequent use. The P2167519B also features large rear wheels that enhance stability and maneuverability, making it easy to navigate through tight spaces or uneven landscapes.

In summary, the Snapper P217019BVE, P216019KWV, P217019BV, and P2167519B models stand out for their powerful engines, self-propelled systems, adjustable cutting decks, and user-friendly features. Designed for both performance and durability, these mowers are perfect for anyone looking to maintain a beautifully manicured lawn with ease and efficiency, providing excellent value in the realm of outdoor power equipment.
Top Page Image Contents