Snapper ZM6102M, MZM2301KH, ZM5202M, MZM5203M Starting & Stopping ENGINE, BLADES, Parking Brake

Page 10

Section 3 - OPERATING INSTRUCTIONS

3.2STARTING & STOPPING – ENGINE, BLADES, PARKING BRAKE

This machine is equipped with dual hydrostatic wheel drive transmissions. Each transmission is controlled by a single motion control lever or joystick. This single control lever (joystick) controls the direction of motion, Forward and Reverse, and the speed of motion. Move the joystick forward to propel the machine forward. Move the control rearward to propel the machine in reverse. The speed of motion is continuously variable from neutral (zero) to maximum. Moving the joystick farther from the neutral position will cause the speed of motion to increase. To turn, move the joystick towards the side you want to turn to. DO NOT make sudden changes in speed or direction. Always slow machine motion before turning. To stop the motion of the machine, bring the joystick back to the neutral position. Engage parking brake.

3.2.1. STARTING ENGINE

When the ignition key is turned the engine will not start or turn over unless the parking brake is engaged and the blade switch is pushed in to “OFF”.

1.Complete pre-start checklist.

2.Sit in operator’s seat.

3.Push blade switch in to “OFF”, blades are in disengaged position and engage parking brake. See Figure 3.2.

4.Move choke control forward to choke position to start a cold engine. See Figure 3.4.

5.Move engine speed control to the Rabbit “FAST” position. See Figure 3.4.

6.Turn key to the start position until engine starts. See Figure 3.5.

CHOKE

ENGINE

CONTROL

SPEED

 

CONTROL

 

 

FIGURE 3.4

“STOP”

POSITION

KEY SHOWN IN “ON” POSITION

FIGURE 3.5

NOTE: If after 5 seconds of cranking the engine does not start, release the key. Attempt starting again after waiting for approximately 20 seconds.

7.After engine starts, move the choke control to the “OFF” or no choke position. Allow a brief warm- up until engine runs smooth.

3.2.2. STOPPING ENGINE

1.Stop engine by turning key to “STOP” position. Move engine speed to the Turtle “SLOW” position and turn key to “STOP”. See Figure 3.5.

WARNING

DO NOT operate blades in reverse. STOP blades. LOOK and SEE behind and down for children, pets, and hazards before and while backing.

3.2.3. STARTING MOWER BLADES

1.Start engine and set engine speed control to the Rabbit “FAST” position. See Figure 3.4.

2.Pull the Blade Switch out to the “ON” position to engage the mower blades. See Figure 3.2.

3.2.4. STOPPING MOWER BLADES

1.Push Blade Switch in to “OFF” position to disengage the blade.

WARNING

Once blades are disengaged, they should come to a complete stop in 7 seconds. If the blades continue to rotate after 7 seconds, the electric clutch should be checked. Replacement of electric clutch may be necessary. Return the machine to an authorized Snapper dealer for replacement. DO NOT CONTINUE to operate mower if blades fail to stop in 7 seconds.

2.Move engine speed control to the Turtle “SLOW” position. Turn key to “STOP” position. Engage parking brake.

11

Image 10
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Mower UnitFrom Previous Column Always begin forward motion slowly and with cautionOperation Important Safety Instructions Table of Contents Introduction NomenclatureSafety Messages and Symbols Safety Messages and Symbols Operating Instructions PRE-START Check ListStopping Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Engine Starting Mower BladesParking Brake Stopping Machine Cutting Height AdjustmentOPERATION- Motion Controls 3.4.1. Driving Machine Service After First 5 Hours Check Mower Blade Change Engine OILCheck Mower Drive Belt After Every 25 Operating HoursBefore Operating Machine Annually END of Each SeasonDeck Removal Power Transfer Shaft Removal Deck Removal from previousNeutral Position Adjustments Side to Side LevelMower Deck Adjustment Levelness Front to Rear LevelEngine Adjustments & Repair Parking Brake AdjustmentMower Blade Replacement Blade Wear Limits Blade Sharpening Mower Drive Belt ReplacementBelt Replacement Belt RemovalBattery Installation Battery Battery RemovalBattery Service NEW Battery Preparation Battery TestingDo not Overfill Mower Spindles Field Serviceable Spindles Bearing ReplacementProblem Probable Cause Corrective Action Trouble Shooting on NextTractor Will Not Move 100 Service Performed EachMAINTENANCE/REPLACEMENT Parts USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series