Snapper NZM27611KH, NZM25611KWV, NZM21521KWV Operating Instructions, PRE-START Check List

Page 9

Section 3 - OPERATING INSTRUCTIONS

3.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

3.1.1.Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.

3.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

3.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 3.1.

SAFE LEVEL

AREA

FIGURE 3.1

3.1.4.Check Blade Switch to insure it works freely.

1.Pull the Blade Switch up to the “ON” position to engage or turn “ON” the mower blades.

2.Push Blade Switch down to the “OFF” position to disengage or turn “OFF” the blades.

BLADE SWITCH

FIGURE 3.2

3.1.5.Clean exterior surfaces of cutting deck, engine and pumps of any accumulation of dirt, grass, oil, etc. Keep engine and pump air intake screens and cooling fins clear at all times.

3.1.6.Add fuel to both tanks of the machine outside where fumes can safely dissipate. Make sure both fuel filler caps are tight. Note the fuel tank selector valve. Refer to engine owner’s manual for fuel specifications.

3.1.7.Adjust position of operator’s seat. The seat is mounted on slides. Locate latch lever beneath the seat. Move lever towards the left and slide seat to the desired position. Release latch. If equipped, adjust seat suspension for operator weight.

3.1.8.Place mower in desired cutting height setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to desired cutting height setting and release latch. Insert stop pin to desired cutting height.

IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.3.

DECK LIFT

LEVER

RELEASE

LATCH

FOOT

ASSIST PEDAL

INSERT STOP PIN

INTO HOLES FOR

DESIRED CUTTING

HEIGHT

FIGURE 3.3

IMPORTANT: This machine is equipped with hydrostatic drive. The direction of motion and the speed of motion are controlled by the left and right motion control levers. A small movement of these controls can cause the machine to move instantly. DO NOT attempt to operate the machine until you read this manual and become familiar with its operation. Practice with the blades “OFF” disengaged, engine speed at a slow setting and in an open area away from obstacles.

WARNING

DO NOT allow operation of the machine by untrained personnel.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Snapper From PreviousMaintenance Table of Contents Nomenclature IntroductionSafety Messages and Symbols RUN PRE-START Check List Operating InstructionsStarting Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Mower Blades Stopping EngineStopping Mower Blades Parking BrakeOPERATION- Motion Controls Driving Machine Cutting Height AdjustmentEngine Must not Start if Stopping MachineEngine should Start if Engine Must Begin to Stop ifCheck Mower Blade Service After First 5 HoursAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal See Figure Neutral Position Adjustments Adjustments & RepairMower Deck & Component Adjustments Neutral Position Adjustments From PreviousMower Deck Adjustment Levelness Side to Side and Front to RearHighest cutting position and recheck side to side Parking Brake AdjustmentTraction Belt Tension Traction Belt ReplacementTracking Adjustment Mower Drive Belt Replacement Belt ReplacementBelt Removal Blade Sharpening Battery Battery Removal Battery InstallationBattery Service 1. Remove battery Battery Testing NEW Battery Preparation 1. Remove battery from cartonDo not Overfill Insert spindle shaft up through the bottom Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Trouble Shooting on NextCorrective Action Machine Will Not Move MAINTENANCE/REPLACEMENT Parts Service Performed Each100 Number USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM21521KWV, NZM27611KH, NZM25611KWV specifications

The Snapper NZM25611KWV, NZM27611KH, and NZM21521KWV are part of the Snapper lineup that exemplifies durability, performance, and innovative technology in outdoor power equipment. Each model is designed to handle various lawn care tasks, making them ideal for both residential and commercial use.

Starting with the Snapper NZM25611KWV, this model features a powerful Briggs & Stratton engine that offers reliable starting and efficient fuel consumption. Its cutting deck is made from durable steel, ensuring longevity and resistance to wear and tear. The 25-inch cutting width allows for efficient mowing in tight spaces, while the adjustable cutting height provides versatility for different grass lengths. The model also incorporates the Easy Start system, allowing users to start the mower with minimal effort. With its self-propelled drive system, the NZM25611KWV makes maneuvering easy, even on challenging terrains.

Next, the Snapper NZM27611KH stands out with its enhanced performance capabilities, featuring a robust Honda engine that is renowned for its reliability and low emissions. The 27-inch cutting deck not only improves cutting efficiency but also includes a mulching option, allowing users to return nutrients to the lawn. Its ergonomic design and intuitive controls enhance user comfort, reducing fatigue during extended use. The NZM27611KH is equipped with superior traction control, making it suitable for various landscapes, including hilly areas.

Finally, the Snapper NZM21521KWV is designed for those who require a more compact solution without sacrificing performance. It features a reliable Kohler engine that delivers consistent power and smooth operation. The 21-inch cutting deck is lightweight and easy to handle, perfect for small to medium-sized lawns. The model includes an integrated bagging system, making it easy to collect clippings for a cleaner finish. The adjustable handle height enhances user comfort, allowing for a more personalized mowing experience.

In summary, the Snapper NZM25611KWV, NZM27611KH, and NZM21521KWV each offer distinct features and technologies tailored to meet different mowing needs. With robust engines, durable cutting decks, and user-friendly designs, they stand as testaments to Snapper's commitment to high-quality lawn care solutions. Whether for residential or commercial use, these models ensure efficient and effective lawn maintenance.
Top Page Image Contents