Snapper NZM19480KWV, NZM21520KWV important safety instructions Cutting Height Adjustment

Page 12

Section 3 - OPERATING INSTRUCTIONS

3.3CUTTING HEIGHT ADJUSTMENT

1.Adjust cutting height, as desired, to any position, using deck lift lever. The release latch should be pulled up when lowering the deck. When raising the deck, the release latch does not have to be pulled up. IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.9 & 3.10.

2.If a specific deck height is desired each time the machine is used, insert the stop pin to desired cutting height. See Figure 3.11.

NOTE: The engine does not have to be running to adjust cutting height.

DECK LIFT

LEVER SHOWN

IN HIGH CUTTING

HEIGHT

PULL RELEASE

LATCH UP WHEN

CHANGING THE

DECK HEIGHT

FIGURE 3.9

DECK LIFT LEVER

SHOWN IN LOW

CUTTING HEIGHT

POSITION

DECK LIFT

ASSIST PEDAL

FIGURE 3.10

WARNING

DO NOT make turns at high speed. Slow machine motion. Move motion control lever gently and with caution. DO NOT make sudden changes in speed or direction.

6 HOLE POSITIONS

FOR STOP PIN

FIGURE 3.11

3.4OPERATION- MOTION CONTROLS

3.4.1.DRIVING MACHINE

1.Start engine. Release parking brake.

2.Move motion control levers gently and with caution in desired direction. See Figure 3.12. FORWARD - Move both control levers forward. REVERSE - Move both control levers rearward. LEFT TURN - Move left control rearward or move right control lever forward.

RIGHT TURN - Move left control forward or move right control lever rearward.

ZERO RADIUS TURN - Move one control lever forward and move the other control lever rearward simultaneously.

REARWARD

MOVEMENT

FORWARD

MOVEMENT

FIGURE 3.12

13

Page 11 Page 13
Image 12
Page 11 Page 13
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Always begin forward motion slowly and with cautionImportant Safety Instructions From PreviousMaintenance From Previous ColumnTable of Contents Introduction NomenclatureSafety Messages and Symbols RUN PRE-START Check List Do not allow operation of the machine by untrained personnelStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Engine Starting Mower BladesStopping Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineStopping Machine Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Riding Mower Lubrication Before Operating MachineAnnually END of Each Season Deck Removal Hydraulic Fluid Filters Adjustments & Repair Neutral Position AdjustmentsNeutral Position Adjustments From Previous Mower Deck & Component AdjustmentsMower Deck Adjustment Levelness Side to Side and Front to RearParking Brake Adjustment Traction Belt Replacement Traction Belt TensionTracking Adjustment Mower Drive Belt ReplacementBelt Replacement Belt RemovalBlade Sharpening Battery Battery Removal Battery Service 1. Remove batteryBattery Installation Battery Testing NEW Battery Preparation 1. Remove battery from cartonDo not Overfill Mower Spindles Field Serviceable Spindles Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Corrective Action Trouble Shooting on NextMachine Will Not Move Service Performed Each MAINTENANCE/REPLACEMENT Parts100 Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM19480KWV, NZM21520KWV specifications

The Snapper NZM19480KWV and NZM21520KWV are standout offerings in the realm of robust mowers, designed to cater to both residential and commercial users seeking efficiency and versatility. These models embody Snapper’s commitment to quality engineering and innovative features that simplify the mowing experience while delivering exceptional performance.

At the heart of both models is a powerful engine, ensuring reliable operation even in the most challenging terrains. The NZM19480KWV features a robust 48-inch cutting deck that allows for a wider cutting path, significantly reducing mowing time. This makes it an optimal choice for larger lawns and landscapes. In contrast, the NZM21520KWV showcases a slightly smaller but efficient 52-inch deck, ideal for tackling intricate yard designs while maintaining maneuverability.

Both mowers are equipped with Snapper's unique Pivoting Front Axle technology, which enhances stability and control. This feature allows the mower to navigate uneven ground smoothly, ensuring a consistent cut regardless of the terrain. The optimized weight distribution contributes to improved traction and handling, making both models suitable for diverse mowing conditions.

The user-friendly design of these mowers is another highlight. They feature a comfortable, adjustable seat with easy-grip controls, allowing operators to navigate their lawns with ease. Additionally, the intuitive dashboard provides real-time information regarding engine performance and fuel levels, enhancing the mowing experience and ensuring that users can focus on achieving the best results.

One of the standout technologies employed in the Snapper NZM19480KWV and NZM21520KWV is the electric start feature. This innovation eliminates the hassle of manual starting, allowing users to begin mowing with the push of a button. Furthermore, both models come with a robust transmission system that ensures smooth acceleration and responsive handling.

In summary, the Snapper NZM19480KWV and NZM21520KWV are exemplary choices for anyone seeking reliable, durable, and efficient mowers. With powerful engines, advanced technologies, and user-friendly designs, these models not only streamline the mowing process but also ensure a pristine lawn appearance. Whether for residential gardening or commercial landscaping, Snapper’s engineering excellence stands out.
Top Page Image Contents