Snapper NZM19480KWV, NZM21520KWV Starting & Stopping ENGINE, BLADES, Parking Brake

Page 10

Section 3 - OPERATING INSTRUCTIONS

ROLL RELEASE: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a wrench to rotate both relief valves counter clockwise to open. After rolling machine, both relief valves must be rotated clockwise to close valves and tighten securely before operating machine. Machine will not move if relief valves are open. See Figure 3.3.

ROTATE RELIEF VALVE

COUNTERCLOCKWISE

TO RELIEVE PRESSURE

RELIEF VALVE

3.2 STARTING & STOPPING – ENGINE, BLADES, PARKING BRAKE

This machine is equipped with dual hydrostatic wheel drive transmissions. Each hydro pump is controlled by a separate motion control lever. The left lever controls the left wheel drive hydro pump and the right lever controls the right wheel drive hydro pump. These levers control the direction of motion, Forward & Reverse, and the speed of motion. Move both levers forward to propel the machine forward. Move both levers rearward to propel the machine in reverse. The speed of motion is continuously variable from neutral (zero) to the maximum. Moving the levers farther from the neutral position will cause the speed of motion to increase. To turn, move the lever on the side to which you want to turn slightly rearward of the other lever. Move levers slowly and carefully. DO NOT make sudden changes in speed or direction. Always slow machine motion before turning. To stop the motion of the machine, bring both motion control levers to the neutral position. Engage parking brake.

3.2.1. STARTING ENGINE

When the ignition key is turned the engine will not start or turn over unless, the blade switch is pushed in to the “OFF” position and the motion control levers are in the neutral lock position. Always engage parking brake before starting engine.

1.Complete pre-start checklist.

2.Sit in operator’s seat.

3.Push blade switch in to “OFF”, blades disengaged position and engage parking brake. See Figure 3.2.

4.Move choke control forward to choke position to start a cold engine. See Figure 3.5.

5.Move engine speed control to the Rabbit “FAST” position. See Figure 3.5.

6.Turn key to the start position until engine starts. See Figure 3.6.

CHOKE

ENGINE

KEY

SPEED

CONTROL

CONTROL

SWITCH

FIGURE 3.3

WARNING

DO NOT disengage the hydro transmission and coast down slopes. DO NOT use Roll Release Control to disengage the hydro transmission unless machine motion can be controlled and engine is off.

MOTION CONTROL LEVERS

SHOWN IN THE NEUTRAL LOCK POSITION

SHOWN FROM OPERATOR’S VIEW POINT

FIGURE 3.5

11

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MID Mount Z-RIDER Zero Turning Hydro Drive Series Important Safety Instructions Always begin forward motion slowly and with cautionImportant Safety Instructions From PreviousMaintenance From Previous ColumnTable of Contents Introduction NomenclatureSafety Messages and Symbols RUN PRE-START Check List Do not allow operation of the machine by untrained personnelStarting & Stopping ENGINE, BLADES, Parking Brake Starting EngineStopping Mower Blades Stopping EngineStarting Mower Blades Parking BrakeCutting Height Adjustment OPERATION- Motion Controls Driving MachineEngine should Start if Stopping MachineEngine Must not Start if Engine Must Begin to Stop ifService After First 5 Hours Check Mower BladeAfter Every 25 Operating Hours 4.3.1. Engine Before Operating Machine Riding Mower LubricationAnnually END of Each Season Deck Removal Hydraulic Fluid Filters Adjustments & Repair Neutral Position AdjustmentsMower Deck Adjustment Levelness Neutral Position Adjustments From PreviousMower Deck & Component Adjustments Side to Side and Front to RearParking Brake Adjustment Traction Belt Replacement Traction Belt TensionBelt Replacement Tracking AdjustmentMower Drive Belt Replacement Belt RemovalBlade Sharpening Battery Service 1. Remove battery Battery Battery RemovalBattery Installation NEW Battery Preparation 1. Remove battery from carton Battery TestingDo not Overfill Mower Spindles Field Serviceable Spindles Bearing ReplacementHydraulic SYSTEM, Purging Problem Probable Cause Corrective Action Trouble Shooting on NextMachine Will Not Move 100 Service Performed EachMAINTENANCE/REPLACEMENT Parts Number USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series

NZM19480KWV, NZM21520KWV specifications

The Snapper NZM19480KWV and NZM21520KWV are standout offerings in the realm of robust mowers, designed to cater to both residential and commercial users seeking efficiency and versatility. These models embody Snapper’s commitment to quality engineering and innovative features that simplify the mowing experience while delivering exceptional performance.

At the heart of both models is a powerful engine, ensuring reliable operation even in the most challenging terrains. The NZM19480KWV features a robust 48-inch cutting deck that allows for a wider cutting path, significantly reducing mowing time. This makes it an optimal choice for larger lawns and landscapes. In contrast, the NZM21520KWV showcases a slightly smaller but efficient 52-inch deck, ideal for tackling intricate yard designs while maintaining maneuverability.

Both mowers are equipped with Snapper's unique Pivoting Front Axle technology, which enhances stability and control. This feature allows the mower to navigate uneven ground smoothly, ensuring a consistent cut regardless of the terrain. The optimized weight distribution contributes to improved traction and handling, making both models suitable for diverse mowing conditions.

The user-friendly design of these mowers is another highlight. They feature a comfortable, adjustable seat with easy-grip controls, allowing operators to navigate their lawns with ease. Additionally, the intuitive dashboard provides real-time information regarding engine performance and fuel levels, enhancing the mowing experience and ensuring that users can focus on achieving the best results.

One of the standout technologies employed in the Snapper NZM19480KWV and NZM21520KWV is the electric start feature. This innovation eliminates the hassle of manual starting, allowing users to begin mowing with the push of a button. Furthermore, both models come with a robust transmission system that ensures smooth acceleration and responsive handling.

In summary, the Snapper NZM19480KWV and NZM21520KWV are exemplary choices for anyone seeking reliable, durable, and efficient mowers. With powerful engines, advanced technologies, and user-friendly designs, these models not only streamline the mowing process but also ensure a pristine lawn appearance. Whether for residential gardening or commercial landscaping, Snapper’s engineering excellence stands out.
Top Page Image Contents