Snapper SZT18336BVE Mower Operation Cutting Height Adjustment, Mower Blade Engagement

Page 11

Section 2 - OPERATING INSTRUCTIONS

2.4 MOWER OPERATION

2.4.1. CUTTING HEIGHT ADJUSTMENT

This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time. Use the release lever when moving deck cutting height to a lower cutting position.

1.Grasp both handles together to disengage latch.

2.Raise or lower handles to desired height.

3.Release lower handle to engage latch. See Figure 2.9.

DECK LIFT

HANDLE

RELEASE

LEVER

CONNECTING BAR OMITTED

IN THIS VIEW FOR CLARITY DETENT PLATE

FIGURE 2.9

IMPORTANT: DO NOT adjust cutting deck with mower blades engaged. Be sure Blade Switch is off before adjusting deck.

2.4.1. MOWER BLADE ENGAGEMENT

1.With engine running, move engine speed control to the Rabbit or “fast” position detent. (Be careful not to slide farther than detent, or choke will engage and engine will stall.)

2.Pull Blade Switch out to its on (‘I’) position to engage mower blade. See Figure 2.10.

2.4.2. MOWING OPERATIONS

1.Please refer to the Important Safety Instructions at the beginning of this manual for instruction on safe mowing practices.

2.Refer to “MOTION CONTROL” earlier in this section to safely and effectively maneuver the machine during mowing operations.

2.4.3. MOWER BLADE DISENGAGEMENT

Push Blade Switch in to its off (‘0’) position to disengage mower blade(s). See Figure 2.10.

WARNING

Blades must stop rotating in 5 seconds or less after blade switch has been turned off. DO NOT operate machine unless blade brake is functioning properly. If adjustment or repair is necessary, refer to Section “Blade Brake Adjustment” or contact your SNAPPER dealer for assistance.

TO START BLADES,

MOVE ENGINE SPEED

CONTROL TO ‘FAST’

DETENT, THEN PULL

BLADE SWITCH OUT.

TO STOP BLADES, PUSH

BLADE SWITCH IN.

FIGURE 2.10

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Number Explanation ScramblerFrom Previous Column Protection for ChildrenProtection Against Tipovers PreparationOperation Safe Handling of GasolineTowing MaintenanceTable of Contents Nomenclature IntroductionMotion Control Levers Cutting Deck Adjustment Handle Forward of Operator SeatEngine Speed & Choke Control Right Control Panel Parking Brake Next to Left Control Panel Applies park brakeStopping Engine PRE-START Check ListEngine Operation 2.2.1. Starting Engine Reverse Motion Motion ControlGetting Ready Forward MotionStopping Motion Conventional TurningLeft turn shown right turn opposite ZERO-TURNINGMower Blade Disengagement Mower Operation Cutting Height AdjustmentMower Blade Engagement Mowing OperationsEngine Must Begin to Stop if Engine Must not Start ifEngine should Start if Single Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeEngine Oil Oil Filter Air Filter Service Every 25 Operating HoursChecking Mower Belt Tension Engine Engine Cooling SystemUnderside View of 33 Deck Check EngineMower Components LubricationMotion Control Pivot Bushings Front Wheel BearingsFront Caster Wheel Pivot Shaft Parking Brake Pivot BushingsStorage OUT of Season Service AnnuallyMotion Control Lever Alignment Motion Control AdjustmentsNeutral Adjustments Tracking AdjustmentsBelt Replacement Mower Drive Belt ReplacementEngine Adjustments & Repair Mower Drive Belt AdjustmentIdler ARM and Belt Guide Detail Blade Brake AdjustmentBelt Replacements From Previous+ 1/16 From Previous Page Checking the 33 Deck BladeDeck Shown Front or Rear View of DeckMower Deck Timing ROD Front to Rear Deck Pitch 38 DecksBlade Sharpening Wheel Brake AdjustmentMower Blade Replacement 4.5.1. Blade Wear Limits Battery Service Blade Replacement ChartMower Blade Replacement 4.5.3. Blade Replacement Battery Battery Removal264 Battery TestingNEW Battery Preparation 1. Remove battery from carton Corrective Action Problem Probable CauseTrouble Shooting on Next Excessive Vibration Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler ZERO-TURN Hydro Drive Series

SZT18336BVE, SZT18386BVE specifications

The Snapper SZT18386BVE and SZT18336BVE are two remarkable zero-turn mowers that combine cutting-edge technology with robust performance, catering to both residential and commercial users who value efficiency and precision in their lawn care tasks.

The SZT18386BVE model features an impressive 38-inch cutting deck, designed to maneuver easily around obstacles while providing a clean and even cut. Its 18-horsepower engine delivers ample power to tackle even the toughest grass conditions, ensuring a seamless mowing experience. The mower's zero-turn capability allows for sharp turns and enhanced agility, making it an ideal choice for landscapes with numerous flower beds or trees. This model is also equipped with a comfortable high-back seat, offering support for extended periods of operation, along with an easy-to-use control panel that places everything within reach for the operator.

On the other hand, the SZT18336BVE boasts a slightly narrower 36-inch cutting deck paired with a 18-horsepower engine, making it an excellent choice for smaller yards that still require the same level of professionalism in their maintenance. This model also integrates Snapper’s innovative Smart Start technology, which ensures quick and reliable engine starts every time. Its compact design means it is easier to store and maneuver in tighter spaces, while still maintaining a high level of cutting performance.

Both models feature durable steel construction, ensuring longevity and resistance to wear and tear. They come with adjustable cutting heights, enabling users to customize their mowing experience according to grass length and health. Additionally, Snapper has incorporated a user-friendly maintenance access panel, which simplifies routine inspections and servicing.

Another key feature is the enhanced wheel and tire design, which provides superior traction and stability on various terrains. This is vital for users who often mow in uneven or sloped areas, as it contributes to safety and efficiency.

With their powerful engines, advanced features, and thoughtful designs, the Snapper SZT18386BVE and SZT18336BVE are positioned as top contenders in the zero-turn mower market. Perfect for homeowners and professionals alike, they deliver a perfect blend of performance, comfort, and reliability, making lawn care a more enjoyable experience.
Top Page Image Contents