Snapper SZT18336BVE, SZT18386BVE Service Annually, Storage OUT of Season

Page 17

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.4SERVICE - ANNUALLY

Perform all maintenance as described in the maintenance schedule.

3.4.1. Engine

Service engine according to engine owner’s manual.

3.4.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.4.3. Oil Filter

Refer to engine owner’s manual for service instructions.

3.4.4. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4.5. Transaxle

IMPORTANT: DO NOT try to open reservoir cap at any time. The transaxle is maintenance free. The transaxle does not require any fluid or any service. If there is any problem: leakage, malfunction or etc. return the SCRAMBLER immediately to the nearest authorized Snapper dealer for service.

3.4.6. Fuel Filter

Service fuel filter as instructed below. Close fuel valve in fuel line. Run engine until engine runs out of fuel. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter. Perform filter change only when fuel line is empty.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. Reinstall hose clamps. See Figure 3.10.

NEW FUEL FILTER

PART NO. 1-4359

HOSE CLAMPS

FIGURE 3.10

3.5 STORAGE (OUT OF SEASON)

Perform the following procedures to insure the SCRAMBLER will operate properly when taken out of storage.

1.Thoroughly clean the SCRAMBLER by removing all grass clippings and debris.

2.Perform maintenance and lubrication as described in the previous sections.

3.Drain fuel from fuel tank into an approved container outdoors away from all sources of ignition.

4.Start engine and allow it to run until engine runs out of fuel. This allows the carburetor and fuel system to remain clean during storage.

5.Remove battery. Refer to Section “BATTERY REMOVAL AND STORAGE”.

6.Close vent on fuel filler cap and fuel valve in fuel line. Remove key.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model Number Explanation ScramblerProtection Against Tipovers Protection for ChildrenPreparation From Previous ColumnOperation Safe Handling of GasolineTowing MaintenanceTable of Contents Nomenclature IntroductionEngine Speed & Choke Control Right Control Panel Cutting Deck Adjustment Handle Forward of Operator SeatParking Brake Next to Left Control Panel Applies park brake Motion Control LeversStopping Engine PRE-START Check ListEngine Operation 2.2.1. Starting Engine Getting Ready Motion ControlForward Motion Reverse MotionLeft turn shown right turn opposite Conventional TurningZERO-TURNING Stopping MotionMower Blade Engagement Mower Operation Cutting Height AdjustmentMowing Operations Mower Blade DisengagementEngine Must Begin to Stop if Engine Must not Start ifEngine should Start if Change Engine OIL Service After First 5 HoursCheck Mower Blade Single Blade DeckChecking Mower Belt Tension Service Every 25 Operating HoursEngine Engine Cooling System Engine Oil Oil Filter Air FilterMower Components Check EngineLubrication Underside View of 33 DeckFront Caster Wheel Pivot Shaft Front Wheel BearingsParking Brake Pivot Bushings Motion Control Pivot BushingsStorage OUT of Season Service AnnuallyNeutral Adjustments Motion Control AdjustmentsTracking Adjustments Motion Control Lever AlignmentEngine Adjustments & Repair Mower Drive Belt ReplacementMower Drive Belt Adjustment Belt ReplacementBelt Replacements Blade Brake AdjustmentFrom Previous Idler ARM and Belt Guide Detail+ 1/16 From Previous Page Checking the 33 Deck BladeDeck Shown Front or Rear View of DeckMower Deck Timing ROD Front to Rear Deck Pitch 38 DecksBlade Sharpening Wheel Brake AdjustmentMower Blade Replacement 4.5.1. Blade Wear Limits Mower Blade Replacement 4.5.3. Blade Replacement Blade Replacement ChartBattery Battery Removal Battery Service264 Battery TestingNEW Battery Preparation 1. Remove battery from carton Corrective Action Problem Probable CauseTrouble Shooting on Next Excessive Vibration Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service Performed Each100 USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler ZERO-TURN Hydro Drive Series

SZT18336BVE, SZT18386BVE specifications

The Snapper SZT18386BVE and SZT18336BVE are two remarkable zero-turn mowers that combine cutting-edge technology with robust performance, catering to both residential and commercial users who value efficiency and precision in their lawn care tasks.

The SZT18386BVE model features an impressive 38-inch cutting deck, designed to maneuver easily around obstacles while providing a clean and even cut. Its 18-horsepower engine delivers ample power to tackle even the toughest grass conditions, ensuring a seamless mowing experience. The mower's zero-turn capability allows for sharp turns and enhanced agility, making it an ideal choice for landscapes with numerous flower beds or trees. This model is also equipped with a comfortable high-back seat, offering support for extended periods of operation, along with an easy-to-use control panel that places everything within reach for the operator.

On the other hand, the SZT18336BVE boasts a slightly narrower 36-inch cutting deck paired with a 18-horsepower engine, making it an excellent choice for smaller yards that still require the same level of professionalism in their maintenance. This model also integrates Snapper’s innovative Smart Start technology, which ensures quick and reliable engine starts every time. Its compact design means it is easier to store and maneuver in tighter spaces, while still maintaining a high level of cutting performance.

Both models feature durable steel construction, ensuring longevity and resistance to wear and tear. They come with adjustable cutting heights, enabling users to customize their mowing experience according to grass length and health. Additionally, Snapper has incorporated a user-friendly maintenance access panel, which simplifies routine inspections and servicing.

Another key feature is the enhanced wheel and tire design, which provides superior traction and stability on various terrains. This is vital for users who often mow in uneven or sloped areas, as it contributes to safety and efficiency.

With their powerful engines, advanced features, and thoughtful designs, the Snapper SZT18386BVE and SZT18336BVE are positioned as top contenders in the zero-turn mower market. Perfect for homeowners and professionals alike, they deliver a perfect blend of performance, comfort, and reliability, making lawn care a more enjoyable experience.
Top Page Image Contents