Snapper SZT18386BVE, SZT18336BVE Problem Probable Cause Corrective Action, Excessive Vibration

Page 28

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

Excessive Vibration

1. Damaged, out of balance or bent mower blades.

1. Service mower blade(s).

 

2. Loose blade components.

2. Service and tighten loose parts.

 

3. Loose or missing air lift (if equipped).

3. Replace air lifts. Tighten to proper torque.

 

4. Lumpy or frayed belt.

4. Replace belt.

 

5. Bent Idler, stationary or spindle pulley.

5. Replace pulley.

Rider Will Not Move Or

1. Motion Control Levers in neutral “N” position.

1.

Move levers in desired position.

Loss Of Traction

2. Roll release lever is in “ROLL” position.

2.

Move roll release lever to the engaged position.

 

3.

Low transmission hydraulic oil level.

3.

Contact authorized SNAPPER dealer.

 

4.

Parking Brake engaged.

4.

Move parking brake to disengaged position.

 

5.

Traction drive belt requires replacement.

5.

Replace traction drive belt.

Blade(s) Not Cutting

1. Blade engagement switch in the “OFF” position.

1.

Move blade switch to the “ON” position.

 

2.

Clutch belt slipping.

2.

Replace clutch belt.

 

3.

Mower belt slipping.

3.

Replace mower belt.

 

4.

Electric clutch not functioning.

4.

Contact authorized SNAPPER dealer.

Cutting Grass

1. Uneven tire pressure.

1.

Bring to proper pressure.

Improperly

2. Cutting height too low or high.

2.

Adjust cutting height.

 

3.

Engine speed too slow.

3.

Move engine speed control to “FAST” position.

 

4.

Forward speed too fast.

4.

Move joystick to a slower speed.

 

5.

Terraced cut, side to side.

5.

Adjust side to side level.

 

6.

Excessive deck pitch, front to rear.

6.

Adjust front to rear pitch.

 

7.

Cutting blade(s) dull or damaged.

7.

Sharpen cutting edges or replace blade(s).

 

8.

Blade belt slipping.

8.

Replace blade belt.

 

9.

Check electric clutch.

9.

Adjust to proper specifications.

 

10. Check clutch belt.

10. Replace clutch belt.

Poor Grass Discharge

1. Engine speed too slow.

1.

Move engine speed control to “FAST” position.

 

2.

Forward speed too fast.

2.

Move joystick to a slower speed.

 

3.

Grass is wet.

3.

Mow when grass is dry.

 

4.

Excessively worn or damaged blade(s).

4.

Service mower blade(s).

 

5.

Build up of grass clippings and debris under deck.

5.

Clean deck.

 

6.

Improper blade(s) installed on deck.

6.

Install proper SNAPPER blades.

 

7.

Blade(s) installed improperly on deck.

7.

Install blades properly.

Battery Will Not Charge

1. Poor cable connections.

1.

Clean cables and battery terminals.

 

2.

Bad battery cell(s).

2.

Replace with new battery.

 

3.

Faulty alternator.

3.

Contact engine manufacturer’s dealer.

Oil Leaking

1. Leaking hose fittings, clamps or reservoir.

1.

Verify fittings and hose clamps are tight.

28

26

Image 28
Contents Scrambler Model Number ExplanationProtection for Children Protection Against TipoversPreparation From Previous ColumnSafe Handling of Gasoline OperationMaintenance TowingTable of Contents Introduction NomenclatureCutting Deck Adjustment Handle Forward of Operator Seat Engine Speed & Choke Control Right Control PanelParking Brake Next to Left Control Panel Applies park brake Motion Control LeversEngine Operation 2.2.1. Starting Engine PRE-START Check ListStopping Engine Motion Control Getting ReadyForward Motion Reverse MotionConventional Turning Left turn shown right turn oppositeZERO-TURNING Stopping MotionMower Operation Cutting Height Adjustment Mower Blade EngagementMowing Operations Mower Blade DisengagementEngine should Start if Engine Must not Start ifEngine Must Begin to Stop if Service After First 5 Hours Change Engine OILCheck Mower Blade Single Blade DeckService Every 25 Operating Hours Checking Mower Belt TensionEngine Engine Cooling System Engine Oil Oil Filter Air FilterCheck Engine Mower ComponentsLubrication Underside View of 33 DeckFront Wheel Bearings Front Caster Wheel Pivot ShaftParking Brake Pivot Bushings Motion Control Pivot BushingsService Annually Storage OUT of SeasonMotion Control Adjustments Neutral AdjustmentsTracking Adjustments Motion Control Lever AlignmentMower Drive Belt Replacement Engine Adjustments & RepairMower Drive Belt Adjustment Belt ReplacementBlade Brake Adjustment Belt ReplacementsFrom Previous Idler ARM and Belt Guide DetailFrom Previous Page Checking the 33 Deck Blade + 1/16Front or Rear View of Deck Deck ShownFront to Rear Deck Pitch 38 Decks Mower Deck Timing RODMower Blade Replacement 4.5.1. Blade Wear Limits Wheel Brake AdjustmentBlade Sharpening Blade Replacement Chart Mower Blade Replacement 4.5.3. Blade ReplacementBattery Battery Removal Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery Testing264 Trouble Shooting on Next Problem Probable CauseCorrective Action Problem Probable Cause Corrective Action Excessive VibrationService Performed Each MAINTENANCE/REPLACEMENT Parts100 USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler ZERO-TURN Hydro Drive Series

SZT18336BVE, SZT18386BVE specifications

The Snapper SZT18386BVE and SZT18336BVE are two remarkable zero-turn mowers that combine cutting-edge technology with robust performance, catering to both residential and commercial users who value efficiency and precision in their lawn care tasks.

The SZT18386BVE model features an impressive 38-inch cutting deck, designed to maneuver easily around obstacles while providing a clean and even cut. Its 18-horsepower engine delivers ample power to tackle even the toughest grass conditions, ensuring a seamless mowing experience. The mower's zero-turn capability allows for sharp turns and enhanced agility, making it an ideal choice for landscapes with numerous flower beds or trees. This model is also equipped with a comfortable high-back seat, offering support for extended periods of operation, along with an easy-to-use control panel that places everything within reach for the operator.

On the other hand, the SZT18336BVE boasts a slightly narrower 36-inch cutting deck paired with a 18-horsepower engine, making it an excellent choice for smaller yards that still require the same level of professionalism in their maintenance. This model also integrates Snapper’s innovative Smart Start technology, which ensures quick and reliable engine starts every time. Its compact design means it is easier to store and maneuver in tighter spaces, while still maintaining a high level of cutting performance.

Both models feature durable steel construction, ensuring longevity and resistance to wear and tear. They come with adjustable cutting heights, enabling users to customize their mowing experience according to grass length and health. Additionally, Snapper has incorporated a user-friendly maintenance access panel, which simplifies routine inspections and servicing.

Another key feature is the enhanced wheel and tire design, which provides superior traction and stability on various terrains. This is vital for users who often mow in uneven or sloped areas, as it contributes to safety and efficiency.

With their powerful engines, advanced features, and thoughtful designs, the Snapper SZT18386BVE and SZT18336BVE are positioned as top contenders in the zero-turn mower market. Perfect for homeowners and professionals alike, they deliver a perfect blend of performance, comfort, and reliability, making lawn care a more enjoyable experience.