Snapper WMR216517B, WMRP216517B important safety instructions Wheel Drive Control Adjustment

Page 14

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.1.3. BLADE SHARPENING

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN

BEYOND ORIGINAL

CUTTING EDGE

22 TO 28º

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.3. Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs.

NOTE: The following sections 4.2 through 4.4 are for self-propelled models only.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1. The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.5.

CLUTCH CABLE

 

VINYL SPRING COVER

 

1/16” TO 1/8”

CLUTCH

CABLE EYE

CLEARANCE

 

UPPER

SPRING HOOK

SPRING

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.5

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Engine Type Series Designation Engine Horse Power Steel Deck Walk Mowers M Model SeriesImportant Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeStarting & Operation Handle Height AdjustmentCutting Height Adjustment StoppingRecycling Operation BAG Slider Fold BAG AS Shown Install Discharge Deflector Slide Deflector Slot Under NUT Check Grease Level in Transmission Service After First 5 Hours 3.2.1. Change Engine OILImportant Drain fuel tank before tipping mower On NextCheck Mower Blade Service AnnuallyStorage Procedure Check Engine Drive BeltNinja Blade Wear Limit Mower Blade Replacement 4.1.1. Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Drive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentReplacing Rubber Driven Disc Replacing Bearing In Driven Disc Assembly Belt Service Engine Drive Belt Replacement Stretch Type BeltsTransmission Poly-V Belt Replacement Pulley PositionTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service Performed EachClean Sponge Element Engine Manual 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Steel Deck Walk Behind Mowers M Model Series
Related manuals
Manual 46 pages 20.32 Kb

WMRP216517B, WMR216517B, WMRP216517B specifications

The Snapper WMRP216517B, also known as WMR216517B, is a powerful walk-behind mower designed for performance, durability, and user convenience. This mower is favored by both homeowners and professionals who require a reliable and efficient cutting solution for medium to large-sized lawns.

One of the main features of the Snapper WMRP216517B is its robust engine. Powered by a reliable 163cc OHV engine, this mower delivers plenty of power for cutting through thick grass and tackling uneven terrain. The self-propelled drive system offers ease of operation, allowing users to maintain a steady pace without exerting too much effort. This feature is particularly beneficial for those who may find traditional push mowers challenging to operate over long distances.

The WMR216517B is equipped with a 21-inch steel cutting deck, which provides an optimal balance between maneuverability and cutting efficiency. This deck size is perfect for efficiently maintaining lawns without being overly cumbersome. The mower also boasts an adjustable cutting height, ranging from 1 inch to 4 inches, allowing users to customize their mowing experience based on grass type and growing conditions.

Another notable characteristic of the Snapper WMRP216517B is its advanced grass management system. It features a three-in-one capability, allowing users to choose between mowing, bagging, or mulching grass clippings. The mulch plug ensures that clippings are finely chopped and returned to the soil, providing natural nutrients to promote a healthier lawn.

User comfort is also prioritized in the design of the WMR216517B. It comes with adjustable ergonomic handles, which can be tailored to the user's height for maximum comfort during operation. The folding handle design makes storage simple, especially in tight spaces.

Additionally, this mower features easy-start technology that reduces starting friction and enhances reliability, ensuring that users can get to mowing without frustrating delays.

In summary, the Snapper WMRP216517B and its variants are excellent choices for anyone in need of a dependable walk-behind mower combining power, versatility, and user-friendly features, making lawn care a more enjoyable task.
Top Page Image Contents