Snapper WMR216517B, WMRP216517B important safety instructions Replacing Rubber Driven Disc

Page 16

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.3.DRIVEN DISC ADJUSTMENT (Continued From Previous Page)

2.Remove driven disc spring from driven disc assembly. Loosen connector hex nut. See Figure

DRIVEN DISC ASSEMBLY

DRIVE

DISC

DRIVEN

DISC

SPRING

TRANSFER

ROD

CONNECTOR

CONNECTOR

HEX NUT

FIGURE 4.9

3.Slide driven disc assembly over to 1/8” from outside edge of drive disc. Maintaining the 1/8” measurement, remove any looseness from the linkage. This can be done by holding the transfer rod and applying pressure to the left (as viewed from operators position). Then retighten the connector hex nut securely. See Figure 4.10. Move ground speed control to the first speed position, then back to the sixth speed position. Recheck the 1/8” measurement described previously. Reinstall driven disc spring to driven disc assembly.

1/8” MEASUREMENT TO

SLIDE DRIVEN

OUTSIDE EDGE OF

DISC ASSEMBLY

DRIVE DISC

TOWARD

 

OUTSIDE EDGE

DRIVE

 

DISC

TRANSFER

ROD

CONNECTOR HEX NUT

 

OUTSIDE

CONNECTOR

EDGE

 

FIGURE 4.10

4.3.4. Replacing Rubber Driven Disc

If the rubber is badly chunked or worn it must be replaced. Install new Driven Disc as follows:

1.Using a small flat blade screwdriver, free the clip from the transfer rod. Then remove the transfer rod from the clip and the speed control rod. See Figure

CONNECTOR

CLIP

TRANSFER

ROD

SPEED

CONTROL

ROD

FIGURE 4.11

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Engine Type Series Designation Engine Horse Power Steel Deck Walk Mowers M Model SeriesImportant Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeHandle Height Adjustment Cutting Height AdjustmentStarting & Operation StoppingRecycling Operation BAG Slider Fold BAG AS Shown Install Discharge Deflector Slide Deflector Slot Under NUT Service After First 5 Hours 3.2.1. Change Engine OIL Important Drain fuel tank before tipping mowerCheck Grease Level in Transmission On NextService Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltBlade Sharpening Mower Blade Replacement 4.1.1. Standard Blade Wear LimitNinja Blade Wear Limit Wheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentReplacing Rubber Driven Disc Replacing Bearing In Driven Disc Assembly Belt Service Engine Drive Belt Replacement Stretch Type BeltsTransmission Poly-V Belt Replacement Pulley PositionTroubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Steel Deck Walk Behind Mowers M Model Series
Related manuals
Manual 46 pages 20.32 Kb

WMRP216517B, WMR216517B, WMRP216517B specifications

The Snapper WMRP216517B, also known as WMR216517B, is a powerful walk-behind mower designed for performance, durability, and user convenience. This mower is favored by both homeowners and professionals who require a reliable and efficient cutting solution for medium to large-sized lawns.

One of the main features of the Snapper WMRP216517B is its robust engine. Powered by a reliable 163cc OHV engine, this mower delivers plenty of power for cutting through thick grass and tackling uneven terrain. The self-propelled drive system offers ease of operation, allowing users to maintain a steady pace without exerting too much effort. This feature is particularly beneficial for those who may find traditional push mowers challenging to operate over long distances.

The WMR216517B is equipped with a 21-inch steel cutting deck, which provides an optimal balance between maneuverability and cutting efficiency. This deck size is perfect for efficiently maintaining lawns without being overly cumbersome. The mower also boasts an adjustable cutting height, ranging from 1 inch to 4 inches, allowing users to customize their mowing experience based on grass type and growing conditions.

Another notable characteristic of the Snapper WMRP216517B is its advanced grass management system. It features a three-in-one capability, allowing users to choose between mowing, bagging, or mulching grass clippings. The mulch plug ensures that clippings are finely chopped and returned to the soil, providing natural nutrients to promote a healthier lawn.

User comfort is also prioritized in the design of the WMR216517B. It comes with adjustable ergonomic handles, which can be tailored to the user's height for maximum comfort during operation. The folding handle design makes storage simple, especially in tight spaces.

Additionally, this mower features easy-start technology that reduces starting friction and enhances reliability, ensuring that users can get to mowing without frustrating delays.

In summary, the Snapper WMRP216517B and its variants are excellent choices for anyone in need of a dependable walk-behind mower combining power, versatility, and user-friendly features, making lawn care a more enjoyable task.
Top Page Image Contents