Hydraulic OIL Reservoirs | Snapper Z-rider specification

WARNING

Handle fuel with care! Use an approved fuel container. DO NOT smoke near open fuel container and keep fuel container away from open flame. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes before refilling. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors. Before attempting any adjustments, maintenance, service, or repairs, stop engine and blade, always remove key from ignition switch, remove spark plug wire(s) and secure wire(s) away from spark plug(s).

STEP 12: MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR

Before making deck leveling adjustments, inflate rear tires to 12 PSI and front tires to 25 PSI. When adjusted correctly, the deck will be level side to side within 1/8”, have a low cut setting of approximately 1” and the blades pitched approximately 3/16” higher at the rear.

A. Place machine on a smooth level surface.

B. Check blade tips by rotating blades until tips are pointing to the sides of the deck. Check the measurement of outside blade tips to the ground on both blades. The measurement of each of the outside blade tips should be within 1/8” of each other. If measurement of the blade tips is not within 1/8”, adjustment should be made to the correct measurement.

C. Move deck lift lever and set the mower deck to the highest cutting position.

D. Relieve tension on deck lift assist spring by loosening nut on eyebolt.

E. Place 1” blocks under the front and rear edge of the mower deck.

F. Move deck lift lever and set the mower deck to a lower cutting position until deck rests on the 1” blocks. G. Loosen the nuts and bolts that secure both front deck support chains. Adjust chains until tight and retighten bolts and nuts. Torque to 70 ft. lbs.

H. Loosen the nuts that secure both rear deck support eyebolts. Adjust to remove slack from both rear chains. Tighten nuts securely.

I. Move deck lift lever and set the mower deck to the highest cutting position and recheck side to side blade tip dimensions. The difference between the two should be 1/8” or less.

NOTE: The deck timing rod is preset at the factory and requires no adjustments.

J. The leveling blocks used in Step E should result in a proper deck pitch. If a pitch adjustment is required, use the two rear deck support eyebolts. Adjust up or down as required.

K. Reinstall deck lift assist spring. Place deck in highest cutting position. Tighten nut on eyebolt until 1 1/4” of threads protrude past end of nut.

STEP 13: HYDRAULIC OIL RESERVOIRS

Check the level of the fluid in both of the fluid reservoirs. The reservoirs are located underneath the operator’s seat. Wipe away all dirt and debris from around reservoir cap before removing. Oil must remain absolutely clean! Check with machine on a level surface with engine “OFF”. Fill reservoir as needed to bring level up. The reservoir is properly filled when the fluid level is 1½” below the top of the filler neck. DO NOT OVER FILL. Use clean, fresh premium automotive oil having a viscosity equivalent to SAE 20W50 API SL. The fluid should be chemically stable, incorporating rust and oxidation inhibitors. Make sure funnels, pouring spouts and oil can are completely clean. Reinstall reservoir cap.

IMPORTANT: Re-check fluid level after operating machine for several minutes and adjust level as needed. If one or both of the wheel drive systems is not pulling properly, the hydraulic system may need to be purged of entrapped air. Refer to

STEP “HYDRAULIC SYSTEM, PURGING”.

STEP 14: TRACKING ADJUSTMENT – TWIN STICK CONTROLS

Start machine. If the machine does not track straight when the Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSI before making this adjustment.

A. Loosen bolts that secure adjustment plates and slide plates all the way forward. Retighten bolts.

B. Start machine and drive in smooth flat open area at maximum forward speed.

C.If machine tracks to the right, loosen bolts that secure the left adjustment plate. Move plate rearward to slow the left wheel. Retighten bolts.

D.If machine tracks to the left, loosen bolts that secure the right adjustment plate. Move plate rearward to slow the right wheel down. Retighten bolts. See Figure 2.

E.Drive machine again. Repeat adjustment as necessary until machine tracks straight.

LEFT SIDE MOTION

CONTROL LEVER

ADJUSTMENT

PLATE

LOOSEN BOLTS.

SLIDE PLATE TO

MAKE MACHINE

TRACK STRAIGHT

FIGURE 2

Z-rider specifications

The Snapper Z-Rider is an innovative zero-turn mower designed to provide exceptional performance and ease of use for homeowners and professional landscapers alike. Renowned for its robust construction and cutting-edge features, the Z-Rider stands out in the competitive lawn care market.

One of the main features of the Snapper Z-Rider is its powerful engine options. Equipped with reliable Briggs & Stratton or Kawasaki engines, the mower provides excellent power and efficiency. The engine options are designed to tackle even the most demanding mowing tasks, allowing users to maintain their lawns effortlessly and effectively.

The Z-Rider's zero-turn capability is another highlight, offering unparalleled maneuverability. With its dual hydrostatic transmission system, operators can effortlessly turn in place, navigate around obstacles, and achieve a precise cut. This feature greatly reduces the mowing time, making it ideal for those with large lawns or commercial properties.

The mower also incorporates a durable, heavy-duty steel frame that ensures stability and longevity. The custom-cut deck is available in different sizes, typically ranging from 42 to 72 inches, allowing users to choose the perfect size for their lawn care needs. The cutting deck features a mulching system that finely chops grass clippings, returning valuable nutrients back to the lawn.

Comfort is a priority with the Snapper Z-Rider. It features an ergonomically designed high-back seat with ample cushioning, allowing for hours of mowing without discomfort. The easy-to-use controls are intuitively positioned, making it simple for users to operate the mower effectively.

Additionally, the Snapper Z-Rider comes equipped with innovative technologies like the Smart Lawn app, which enhances user experience by providing maintenance reminders and tips for optimal performance. This connectivity allows users to keep track of their mower’s status and schedule care when needed, adding to the overall convenience.

Safety features are also prioritized in the Z-Rider, with a dedicated safety switch that automatically shuts off the engine when the operator leaves the seat. This ensures peace of mind during operation, particularly in busy environments.

In conclusion, the Snapper Z-Rider is a top choice for those seeking a powerful, efficient, and user-friendly zero-turn mower. Its combination of robust construction, advanced technology, comfort, and safety features make it a reliable tool for achieving beautifully maintained lawns. Whether for residential or commercial use, the Snapper Z-Rider delivers exceptional performance every time.