Snapper ZF2500K, ZF2500KH, ZF2200K, ZF5200M, ZF6100M important safety instructions Troubleshooting

Page 20

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

 

 

Starter Will Not Crank

1. Battery dead.

1.

Service battery.

 

 

 

 

 

 

Engine

2. Blown fuse.

2.

Replace fuse.

 

 

 

 

 

 

 

3.

Electrical connections loose or corroded.

3. Clean and check connections for good contact.

 

 

 

 

 

 

 

 

4.

Defective ignition switch.

4.

Contact authorized SNAPPER dealer.

 

 

 

 

 

Engine Will Not Start

1. Blade engagement switch in the “ON” position.

1. Move blade engagement switch to “OFF”.

 

 

 

 

 

 

 

 

2.

Park brake not set.

2.

Set park brake.

 

 

 

 

 

 

 

 

3.

Fuel tank empty.

3.

Fill fuel tank with fresh fuel.

 

 

 

 

 

 

 

 

4.

Engine needs choking.

4.

Move choke control to “CHOKE” position.

 

 

 

 

 

 

 

 

5.

Spark plug wire disconnected.

5.

Place spark plug wire onto spark plug.

 

 

 

 

 

 

 

 

6.

Battery weak or dead.

6.

Service battery.

 

 

 

 

 

 

 

 

7.

Faulty parking brake, blade or ignition switch.

7.

Contact authorized SNAPPER dealer.

 

 

 

 

 

 

Engine Stalls After

1. Operator not in seat.

1.

Sit in operator’s seat.

 

 

 

 

 

 

Running

2. Choke control in the “CHOKE” position.

2.

Move choke control to “OFF” position.

 

 

 

 

 

 

 

 

3.

Fuel tank empty.

3.

Fill with fuel to proper level.

 

 

 

 

 

 

 

 

4.

Engine air pre-cleaner and or air cleaner dirty.

4.

Clean free of all debris.

 

 

 

 

 

 

 

 

5.

Spark plug defective or gap set improperly.

5.

Service spark plug.

 

 

 

 

 

 

 

 

6.

Fuel filter stopped up.

6.

Replace fuel filter.

 

 

 

 

 

 

 

 

7.

Water, debris or stale fuel in fuel system.

7.

Drain and clean fuel system.

 

 

 

 

 

 

Engine Loses Power

1. Excessive load on engine.

1.

Lessen load.

 

 

 

 

 

 

 

 

2.

Engine air pre-cleaner or air cleaner dirty

2.

Clean or replace filters.

 

 

 

 

 

 

 

 

3.

Engine oil level low.

3.

Fill with engine oil to proper level.

 

 

 

 

 

 

4. Engine cooling fins & air intake screen excessively dirty.

4. Clean cooling fins, air intake screen of all debris.

 

 

5.

Spark plug faulty.

5.

Service spark plug.

 

 

6.

Water, debris or stale fuel in fuel system.

6.

Drain and clean fuel system.

 

 

 

 

 

Engine Backfires When

1. Throttle control set too “FAST”.

1. Set throttle control to “SLOW” and allow engine

to

Turned To “STOP”

 

 

 

idle. Then, turn key to “OFF”.

 

Excessive Vibration

1. Damaged or bent mower blades.

1.

Service mower blade(s).

 

 

 

 

 

 

 

 

2.

Loose blade components.

2.

Service and tighten loose parts.

 

 

 

 

 

 

 

 

3.

Loose or missing air lift (if equipped).

3.

Replace air lifts. Tighten to proper torque.

 

 

 

 

 

 

 

(Trouble Shooting Continued on Next Page)

20

Image 20
Contents Model Number Explanation Mower UnitPreparation Protection for ChildrenProtection Against Tipovers Maintenance OperationTable of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Stopping ENGINE, Blades & Parking Brake Starting EngineCutting Height Adjustment Stopping Engine 2.2.1. EngineStarting Mower Blades Stopping Mower BladesOperation Motion Control 2.3.1 Driving Machine Service After First 5 Hours Change Engine OILCheck Mower Blade Tighten to Mountingfoot PoundsCheck Mower Drive Belt After Every 25 Operating HoursAnnually END of Each Season Riding Mower LubricationBefore Operating Machine Power Transfer Shaft Removal Deck RemovalAdjustments & Repair Neutral Position AdjustmentsParking Brake Adjustment Engine Adjustments & RepairMower Blade REPAIR/REPLACEMENT Blade Wear Limits Mower Drive Belt ReplacementBlade Sharpening Engine Belt RemovalEngine Belt Replacement Battery Battery RemovalBattery Installation Battery ServiceDo not Overfill Battery TestingNEW Battery Preparation Remove NUT Remove Belt From Spindle Remove Blade Bolt Troubleshooting Problem Probable Cause Corrective ActionTractor Will Not Move USE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance OUT Front Z-RIDER Zero Turning Hydro Drive Series