Cisco Systems 1500 Series manual Mounting the Access Point on a Pole

Page 17

Chapter 2 Mounting Instructions

Mounting the Access Point

C i s c o C o n f i d e n t i a l - D r a ft 1

Caution When the product is installed outside of the building, and the DC power/Ethernet connection is used, this cabling should be installed in accordance with the requirements of a Class 2 circuit, as detailed in Article 725 of the National Electric Code (NEC). Such requirements include, but are not limited to, routing the Class 2 cabling away from AC power lines and AC building wiring, and limiting the exposed cable runs external to the building to less than 140 ft (42 m) – or is directly buried or in underground conduit, where a continuous metallic cable shield or a continuous metallic conduit containing the cable is bonded to each building grounding electrode system. If such installation methods are not used, the cabling must be installed according to the requirements for telecommunication circuits (TNV) as detailed in Article 800, which includes requirements for a Listed primary protector upon entering the building, and limits the installation to only Listed networking equipment designed to accommodate telecommunication interfaces.

Use only the specified power injector (AIR-PWRINJ1500=) for the access point. This power injector is designed to meet the power requirements of the access point and is a listed Class 2 Limited Power Source (LPS).

Tip To forward bridge traffic, add a switch between the power injector and controller. Refer to the Deployment Guide: Cisco Mesh Networking Solution for more information.

Step 3 Ensure the antennas are connected to the access point before you apply power to the access point.

Step 4 Connect a shielded outdoor-rated Ethernet cable (such as AIR-ETH1500-150=) between the power injector and the access point’s Ethernet connector (see Figure 2-2).

Note You should hand-tighten the access point Ethernet cable connector until the connector locks.

Warning Use the captive connector cap on the unused mil spec connector to prevent water intrusion and possible safety hazards. Statement 362

Step 5 When using the optional Cisco external omnidirectional antennas, connect them to the access point as shown in Figure 2-1. When using other Cisco external antennas, mount them as directed by the installation documentation that shipped with the antennas.

Step 6 When using optional third-party external antennas, mount and connect them as described in the installation documents that shipped with the antennas.

Step 7 Continue with the “Grounding the Access Point” section on page 2-21.

Mounting the Access Point on a Pole

When installing an access point on a pole or mast, you should use the optional Cisco pole mount kit. To mount the access point on a pole, perform these steps:

Cisco Aironet 1500 Series Outdoor Mesh Access Point Hardware Installation Guide

 

OL-9977-05

2-17

 

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Mounting Instructions Tools and Materials Unpacking the Access PointPackage Contents Safety Information Safety Precautions FCC Safety Compliance StatementAvoiding Damage to Radios in a Testing Environment Site Surveys Installation GuidelinesBecoming Familiar with Access Point Installation Components Before Beginning the InstallationComponents in a Typical Access Point Installation Access Point Connectors Choose Security MAC Filtering New Enabling Zero Touch Configuration on the ControllerInstallation Options Mounting the Access PointConfiguring a RAP Access Point Mounting Orientations Preferred Horizontal Orientation 5illustrates the access point vertical orientation Access Point Mounting Plate and Carriage Bolts Mounting Plate Screw Hole Locations Roof-Overhang InstallationMounting the Access Point on a Pole Adjustment Plate Attached to the Mounting Plate Pole Clamp and Clamp Adjustment Plate Mounted on a Pole 10 Access Point Attached to the Pole Clamp Streetlight Pole Installations Grounding the Access PointS c o C o n f i d e n t i a l D r a ft 11 Using the Streetlight Power Tap Adapter What to Do Next

1500 Series specifications

Cisco Systems has long been a forerunner in networking and cybersecurity solutions, and the Cisco 1500 Series represents a significant advancement in their offerings. Designed primarily for industrial environments, this series aims to facilitate reliable and secure connectivity in challenging conditions. The Cisco 1500 Series includes various models tailored to a wide range of applications, including critical infrastructure, smart cities, and the Internet of Things (IoT).

One of the standout features of the Cisco 1500 Series is its rugged design. Built to withstand extreme temperatures, vibration, and moisture, the devices are suitable for deployment in outdoor settings and industrial applications. This robust construction ensures that the devices remain operational under harsh conditions, promoting uninterrupted service delivery.

Moreover, the Cisco 1500 Series is equipped with advanced wireless technologies, including Wi-Fi 6 and secure mesh networking capabilities. Wi-Fi 6 provides higher throughput, better efficiency, and improved performance in environments crowded with multiple devices. The secure mesh functionality allows for seamless connectivity across large areas, enabling organizations to expand their networks without sacrificing performance or security.

Security is another critical aspect of the Cisco 1500 Series. With integrated security protocols and robust encryption methods, these devices safeguard sensitive data transmission. The series supports end-to-end encryption and access control measures, helping organizations comply with stringent regulatory requirements while protecting against cybersecurity threats.

Management and configuration of the Cisco 1500 Series are simplified through Cisco's cloud management solutions. Users can deploy, manage, and monitor their networks remotely, allowing for efficient oversight and real-time troubleshooting. This ability to manage devices from a centralized interface reduces the complexity often associated with network administration.

Additionally, the Cisco 1500 Series supports various IoT protocols, making it ideal for organizations looking to implement smart technologies. The series is compatible with standards such as MQTT and CoAP, enhancing interoperability among devices and systems, and enabling the creation of more efficient and intelligent environments.

In summary, the Cisco 1500 Series provides robust, secure, and efficient networking solutions suited for industrial and outdoor applications. Its rugged design, advanced wireless capabilities, integrated security features, and support for IoT protocols make it a compelling choice for organizations looking to enhance their connectivity and infrastructure reliability.
Top Page Image Contents