Cub Cadet 977A, E977C manual Operating Your Lawn Mower, Gas & Oil Fill-Up, Before Starting Mower

Page 10

SECTION 5: OPERATING YOUR LAWN MOWER

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

NOTE: For shipping purposes your mower is set with the wheels in a low cutting height position. For best results, raise the cutting position until it is determined which height is best for your lawn. See the Adjustment Section for details.

Gas & Oil Fill-Up

•Check oil level and add oil if necessary. Follow relevant instructions in the engine manual for this.

•Service the engine with gasoline as instructed in the engine manual.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

Before Starting Mower

Charging the Battery (Model E977 only)

IMPORTANT: Use only the battery charger supplied with this mower.

WARNING: The battery contains corrosive fluid and toxic material; handle with care. Keep away from children. Do not puncture, disassemble, mutilate or incinerate the battery. Explosive gases could be vented during charging or discharging. Use in a well ventilated area, away from sources of ignition.

Protective

Cap

Battery

pack lead

outlet. See Figure 11. Follow this order of action every time you charge the battery.

•Charge battery for 16 hours before initial use. Do not charge longer than 20 hours.

•After charging, disconnect battery charger plug from household outlet first, then disconnect charger lead from battery pack lead.

WARNING: Do not remove the battery pack from the handle panel for any reason other than replacement. When replacing the battery pack, refer to instructions on page 16.

•Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

•Check for proper drive clutch operation using the neutral adjustment test described below.

Neutral Adjustment Test

To perform the neutral adjustment test, answer the following questions.

•With the drive clutch control released, push mower forward and pull it backward. Does it move freely?

•Squeeze the drive clutch control and pull the mower backward. Do the rear wheels lock?

•Is the drive clutch control cable free of kinks or sharp bends?

•If you answered “yes” to all three questions, your mower passed the test and you can start your mower.

•If you answered “no” to any of the three questions, you will have to adjust the drive clutch control as instructed in the ADJUSTMENT SECTION.

Starting Engine

WARNING: Be sure no one other than the operator is standing near the lawn mower while starting engine or operating mower.

WARNING: Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

WARNING: Keep hands, feet, hair and loose clothing away from any moving parts on engine and lawn mower.

Figure 11

•Remove the protective cap from the end of the battery pack lead. Always plug charger lead into battery pack lead first, and then insert battery charger plug into 120 volt standard household

WARNING: When starting the unit for the first time, face the mower against a wall or a fence. Start the unit and if it shows any signs of motion while the drive clutch control is still disengaged, shut engine off immediately.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationChildren ServiceSlope Operation Do NotGeneral Service Your ResponsibilitySlope Gauge Removing Unit From Carton Before AssemblyAssembling Your Lawn Mower Loose Parts in CartonAttaching The Grass Bag Attaching Starter RopeAttaching Side Discharge Chute Know Your Lawn Mower Before Starting Mower Operating Your Lawn MowerGas & Oil Fill-Up Starting EngineMulching Using Your Lawn MowerStopping Engine Bagging Grass ClippingsDrive Clutch Control Engine AdjustmentsCutting Height Shift Lever CableEngine Care Cleaning MowerMaintaining Your Lawn Mower LubricationDrive Belt Replacement Blade CareWheel Hex Bolt Cutting Height Adjustment In-line Fuse Replacing Battery PackReplacing Rear Flap Storing Your Lawn MowerTroubleshooting Problem Cause RemedyParts List for Models 977 & E977 Models 977 & E977 Models 977 & E977 Part Description Model E977 Engine Manual for Kawasaki Engine Fuel Information Emission Control InformationExhaust Emission Control System Engine Emissions Compliance Period Installation InstructionsMaintenance and Warranty Tampering with Emission Control System ProhibitedGeneral Information Location of Safety Related LabelsTune-up Specifications Engine Serial NumberFuel And Oil Recommendations PreparationOperating StartingStopping Oil Level Check AdjustmentEngine Speed Adjustment Oil ChangeAir Cleaner Service Cooling System CleaningFoam Element Paper Element StorageRecommended Spark Plug Page Specifications Troubleshooting GuideEnvironmental Protection Page Limited Liability MANUFACTURER’S Limited Warranty for

E977C, 977A specifications

The Cub Cadet 977A and E977C are powerful lawn care machines designed for both residential and commercial use. These models stand out for their robust construction, reliability, and advanced features, making them popular choices among homeowners and professional landscapers alike.

One of the main features of the Cub Cadet 977A is its powerful engine. Equipped with a high-performance, overhead valve (OHV) engine, it ensures efficient power output and better fuel economy. This engine configuration allows for smoother operations and greater durability, even in tough mowing conditions. Similarly, the E977C model offers a strong engine option, optimized for both performance and lower emissions, promoting environmental responsibility.

Both models feature a cutting deck with a generous width that enhances productivity. The Cub Cadet 977A comes with a 54-inch cutting deck, while the E977C is fitted with a versatile 60-inch deck. The larger cutting area allows users to cover more ground in less time, making them ideal for larger lawns and landscapes. Additionally, they offer multiple cutting height adjustments, so users can customize their mowing height according to their specific lawn care needs.

The innovative Turf Saver tires provide excellent traction and minimize lawn damage during operation. The tread design helps in maneuverability, making it easier to navigate around obstacles and tight spaces. Moreover, the ergonomic controls and comfortable seating enhance the driver’s experience, allowing for long periods of mowing without discomfort.

Both the 977A and E977C incorporate advanced technologies such as hydrostatic transmission for seamless speed control. This feature ensures smooth acceleration and deceleration, allowing the operator to focus on precision cutting rather than shifting gears. The models also include a rugged chassis design, which provides stability when tackling uneven terrains.

For ease of maintenance, both models are equipped with easy-access service points, simplifying routine checks and oil changes. Furthermore, they are compatible with various attachments and accessories, like baggers and mulch kits, making them versatile for different lawn care tasks.

In summary, the Cub Cadet 977A and E977C are distinguished by their powerful engines, wide cutting decks, advanced transmission systems, and ergonomic designs. These characteristics make them effective, efficient, and easy to use, positioning them as excellent investments for anyone looking to maintain a pristine lawn or landscape.
Top Page Image Contents