Cub Cadet E977C, 977A manual Maintaining Your Lawn Mower, Cleaning Mower, Engine Care, Lubrication

Page 13

SECTION 7: MAINTAINING YOUR LAWN MOWER

WARNING: Always stop the engine and disconnect the spark plug wire before performing any maintenance work or adjustments on your lawn mower.

Cleaning Mower

The underside of the mower deck should be cleaned after each use to prevent any build-up of debris. If allowed to accumulate, it will cause rust and corrosion.

NOTE: We do not recommend the use of pressure washers or garden hose to clean your unit. These may cause damage to electric components, spindles, pulleys, bearings, or the engine. The use of water will result in shortened life and reduce serviceability.

•Disconnect spark plug wire.

•Drain the gasoline from the lawn mower, or place a piece of plastic under the gas cap.

•Tip the mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold the mower firmly.

•Scrape and clean the underside of the deck with a suitable tool. Do not spray with water.

•Put the mower back on its wheels on the ground. If you had put plastic under the gas cap, make sure to remove it now.

WARNING: Never tip the mower more than 90 degrees in any directions and do not leave the mower tipped for any length of time. Oil can drain into the upper part of the engine causing a starting problem.

Engine Care

A list of key maintenance jobs required for good performance by the mower is given below. Follow the accompanying engine manual for detailed list and instructions.

•Change engine oil regularly, as instructed in the engine manual. Check oil level before starting engine every time. Change oil while the engine is warm, not hot or cold.

•Service foam filter in the air cleaner every 25 hours of use and replace the paper filter component every 100 hours. You may have to service the air filter more frequently if you are operating the mower under extremely dusty conditions.

•Clean the engine periodically. Remove dirt and debris with a cloth or brush.

•Clean the spark plug and reset the gap to .030” at least once a season. Refer to the engine manual for correct spark plug type.

•Inspect muffler periodically, and replace if necessary. Damaged mufflers or spark arresters can create a fire hazard. Make sure to avoid muffler and surrounding areas while the mower engine is hot because temperature of these areas of the engine may exceed 150o F.

Lubrication

Refer to the lubrication chart in Figure 15.

Blade Control Handle

•Lubricate the pivot points on the blade control handle at least once a season with light oil. The blade control must operate freely in both directions.

Rear Discharge Door

•Lubricate the torsion spring and the pivot point on each end of the rear discharge door using a light oil. This will prevent rusting of the discharge door.

Wheels

•Lubricate the wheels and bearings, if so equipped, at least once a season with light oil or engine oil. Also, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil.

Engine

•Follow the engine manual instructions and recommended schedule for lubricating engine components.

Lubricate

Lubricate

Lubricate

Figure 15: Lubrication Chart

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation ServiceChildren Do NotYour Responsibility General ServiceSlope Gauge Assembling Your Lawn Mower Before AssemblyRemoving Unit From Carton Loose Parts in CartonAttaching The Grass Bag Attaching Starter RopeAttaching Side Discharge Chute Know Your Lawn Mower Gas & Oil Fill-Up Operating Your Lawn MowerBefore Starting Mower Starting EngineStopping Engine Using Your Lawn MowerMulching Bagging Grass ClippingsCutting Height Engine AdjustmentsDrive Clutch Control Shift Lever CableMaintaining Your Lawn Mower Cleaning MowerEngine Care LubricationBlade Care Drive Belt ReplacementWheel Hex Bolt Cutting Height Adjustment Replacing Rear Flap Replacing Battery PackIn-line Fuse Storing Your Lawn MowerProblem Cause Remedy TroubleshootingParts List for Models 977 & E977 Models 977 & E977 Models 977 & E977 Part Description Model E977 Engine Manual for Kawasaki Engine Fuel Information Emission Control InformationExhaust Emission Control System Maintenance and Warranty Installation InstructionsEngine Emissions Compliance Period Tampering with Emission Control System ProhibitedTune-up Specifications Location of Safety Related LabelsGeneral Information Engine Serial NumberPreparation Fuel And Oil RecommendationsOperating StartingStopping Engine Speed Adjustment AdjustmentOil Level Check Oil ChangeAir Cleaner Service Cooling System CleaningFoam Element Paper Element StorageRecommended Spark Plug Page Specifications Troubleshooting GuideEnvironmental Protection Page Limited Liability MANUFACTURER’S Limited Warranty for

E977C, 977A specifications

The Cub Cadet 977A and E977C are powerful lawn care machines designed for both residential and commercial use. These models stand out for their robust construction, reliability, and advanced features, making them popular choices among homeowners and professional landscapers alike.

One of the main features of the Cub Cadet 977A is its powerful engine. Equipped with a high-performance, overhead valve (OHV) engine, it ensures efficient power output and better fuel economy. This engine configuration allows for smoother operations and greater durability, even in tough mowing conditions. Similarly, the E977C model offers a strong engine option, optimized for both performance and lower emissions, promoting environmental responsibility.

Both models feature a cutting deck with a generous width that enhances productivity. The Cub Cadet 977A comes with a 54-inch cutting deck, while the E977C is fitted with a versatile 60-inch deck. The larger cutting area allows users to cover more ground in less time, making them ideal for larger lawns and landscapes. Additionally, they offer multiple cutting height adjustments, so users can customize their mowing height according to their specific lawn care needs.

The innovative Turf Saver tires provide excellent traction and minimize lawn damage during operation. The tread design helps in maneuverability, making it easier to navigate around obstacles and tight spaces. Moreover, the ergonomic controls and comfortable seating enhance the driver’s experience, allowing for long periods of mowing without discomfort.

Both the 977A and E977C incorporate advanced technologies such as hydrostatic transmission for seamless speed control. This feature ensures smooth acceleration and deceleration, allowing the operator to focus on precision cutting rather than shifting gears. The models also include a rugged chassis design, which provides stability when tackling uneven terrains.

For ease of maintenance, both models are equipped with easy-access service points, simplifying routine checks and oil changes. Furthermore, they are compatible with various attachments and accessories, like baggers and mulch kits, making them versatile for different lawn care tasks.

In summary, the Cub Cadet 977A and E977C are distinguished by their powerful engines, wide cutting decks, advanced transmission systems, and ergonomic designs. These characteristics make them effective, efficient, and easy to use, positioning them as excellent investments for anyone looking to maintain a pristine lawn or landscape.
Top Page Image Contents