Cub Cadet 23HP Z-Force 50 service manual Operating Instructions, General, When Mowing

Page 9

OPERATING INSTRUCTIONS

Figure. 1

Hour Meter

Electric Blade

Clutch Switch

 

Ignition Switch

A.General

1.When Mowing:

a.Keep adults, children, and pets away from the area to be mowed.

b.When operating this mower, in the forward direction, do not allow the steering levers to return to neutral on their own. Always maintain a firm grip on the levers, operate them smoothly and avoid any sudden movements of the levers when starting and stopping.

c.If the mower is equipped for side dis- charge, never use the mower without the discharge chute installed and placed in the down position.

d.Always remove debris and other objects from the area to be mowed (Note: debris and loose grass will reduce traction).

e.Mow only in daylight or good artificial light.

f.Watch for holes, sprinkler heads, and other hidden hazards.

g.Avoid driving too close to trees, creeks, ditches, sand traps, and other obstacles.

h.Before backing up, check behind and watch where you are going.

i.Always reduce speed when making a turn, and when grass is wet.

j.Always mow across slopes, never up and down the slope. Do not operate on steep slopes and slow down before turning.

Avoid turning downhill if possible, start at the bottom and work up to the top. Use extra care and go slowly when turning downhill. Control the speed and direction of the zero turn machine “primarily” with the speed/directional control (lap bar) of the downhill side of the machine...I.E.,

Figure. 2

Choke

Engine throttle

maintain the uphill side lap bar “essen- tially” in a fixed position.

k.Be careful when crossing gravel paths or roadways. Always turn off the blade clutch switch and wait until the blades stop rotat- ing and raise the cutting deck to the trans- port position. Always allow other vehicles to have the right of way.

l.If you hit a solid object while mowing, turn off the blade clutch switch, place the steer- ing levers in the neutral, opened-out posi- tion, move the throttle to slow, set the parking brake, shut off the engine, and take the key from the ignition switch. Inspect for damage. Repair the damage. Make sure the blades are in good condition and that the blade bolts are tight before restarting the engine.

m.Never leave the mower unattended without performing the following: turn off the blade clutch switch, placing the steering levers in the neutral open-out position, moving the throttle to slow, setting the parking brake, shutting off the engine and taking the key from the ignition switch.

n.Never walk or stand on the discharge side of the mower when the engine is running. Turn off the blade clutch switch if another person approaches while you are operat- ing the mower.

o.Never attempt to operate the traction unit without having the mowing deck attached.

p.Keep the mower and especially the engine and hydraulic components clean and free of grease, grass, and leaves to reduce the chance of fire and permit proper cooling.

9

Image 9
Contents Hydrostatic Zero-Turn Residential Riding Mower Table of Contents Forward Safe Operation Practices General Safety OperationsSlope Operation Service Routing Safety Decals and LabelsSpecifications When Mowing Operating InstructionsGeneral To Mow Grass and Produce a Striped Pat- tern Safety Awareness when MowingSteering Levers Brake Check the fluid levels and tires Initial AdjustmentsLubricate all fittings listed in the mainte- nance section Zero Turn Break-In And Operating ProceduresOrientation Initial OperationStart the Engine Maintenance Service Cleaning your DeckParking the Mower Mower Deck Removing the Mower DeckChanging a Blade Hydrostatic Drive System Changing the Spindle AssemblySharpening the Blade Changing the Blade Drive BeltsInstalling the Battery Battery RemovalElectrical Circuit Specific Gravity Freezing Temp FPage Tires BrakesInflation Pressure Storage Hydraulic SystemDaily Checks Maintenance ScheduleEvery 25 Hour Checks Every 50 Hour ChecksIf Mower is so equipped OIL ChartEngine RPM Check and Adjustment High Speed Tracking AdjustmentLap Bar Adjustment Deck Corner Ball Wheel Roller SettingsDeck leveling Procedure Deck Center Anti-Scalp RollerAdjust as necessary to 8-10 psi Wiring Diagram Slope Gauge Maintenance Record Maintenance Record Maintenance Record MANUFACTURER’S Limited Warranty for How to obtain serviceItems not covered