Cub Cadet 5234D manual Using the Hitch Plate, Tractor Weighting, Front Weights

Page 21

USING THE HITCH PLATE

Use only the hitch plate (Refer to Figure 22), for towing pull-behind equipment (carts, trailers, etc.) or dragging loads.

Raise the lower links of the three point hitch to their highest position to prevent interference with the towed equipment.

IMPORTANT: When transporting pull-behind equipment on public roadways, always use a safety chain to supplement the connection between the tractor and towed equipment. The safety chain must have a strength rating equal to or greater than the gross weight of the equip- ment being towed.

TRACTOR WEIGHTING

When implements are installed on either the front or rear of the tractor, the normal balance of the tractor is altered.

As a rear mounted implement is raised to the transport position, the balance point of the tractor shifts rearward, which may result in a loss of steering control and tractor stability.

When a front mounted implement is raised, the balance point shifts forward and may result in a loss of traction and stability.

To counterbalance these weight shifts, weight should be added to the tractor in the form of either front cast iron weights, a rear weight box, and/or liquid tire ballast. Only enough weight should be added to obtain good traction, control, and stability. Excessive weight will unnecessarily load down the tractor’s engine and transmission.

INSTALL ONLY EQUIPMENT APPROVED FOR USE ON THE 5000 SERIES TRACTOR.

Front Weights

To counterbalance three point hitch mounted equipment, a weight bracket/bumper kit and cast iron weights are available from your Cub Cadet dealer. Refer to the Weighting Table for the proper ballast to be added to the front of the tractor.

Weighting the Rear of the Tractor

To counterbalance front mounted equipment, use a rear weight box, and/or liquid ballast in the rear tires. Refer to the Weighting Table for the proper ballast to be added to the rear of the tractor.

NOTE: Consult with your Cub Cadet dealer about having liquid ballast added to your tires, and for any special maintenance after the procedure is performed. Because special equipment and a familiarity with the practice is required, only a qualified tire technician should perform this procedure.

TRACTOR WEIGHTING TABLE

Equipment Installed

Method of Weighting

Weight Required

on Tractor

 

 

Front Loader

Rear Weight Box AND Bal-

400 pounds in weight box (** with center of gravity approx. 33"

 

last Added to Rear Tires

from center of rear axle and 20" above ground-See note below)

 

 

AND a 86 pounds of liquid ballast added to each rear tire.

Front Loader and

Ballast Added to Rear Tires

86 pounds of liquid ballast added to each rear tire

Appoved Rear Mounted

 

 

Equipment

 

 

Rear Mounted Finish

Front Weight Bracket and

A minimum of four suitcase weights (168 pounds)

Mower

Suitcase Weights

 

Rear Mounted Tiller

Front Weight Bracket and

A minimum of two suitcase weights (84 pounds)

 

Suitcase Weights

 

Rear Mounted Blade,

Front Weight Bracket and

A minimum of two suitcase weights (84 pounds)

Box Blade, Rake

Suitcase Weights

 

Rear Mounted Post Hole

Front Weight Bracket and

A minimum of four suitcase weights (168 pounds)

Digger

Suitcase Weights

 

Front Snow Thrower

None Required

None Required

Front Blade

None Required

None Required

**If the center of gravity of the additional weight is positioned closer to the rear axle and higher from the ground, more weigth must be added. If the additional weight is carried farther from the axle and lower, less weight may be used.

21

Image 21
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTable of Contents Calling Service InformationTo the Owner Rops Information Plate Recording Model and Serial Number InformationGeneral Operation Important Safe Operation PracticesDo not Slope OperationService Safety Frame RopsChildren Operating the PTOPage Battery Warning Label Located Under Hood Safety LabelsFAN Warning Label Located on Each Side of Radiator PTO Warning Label Located on Rear PTO ShieldControls and Features Ignition Switch PTO SwitchSteering Wheel Throttle HandlePTO Reverse Override Switch Seat Adjustment LeverHand Holds Transmission 4WD Shift LeverHeadlight Switch Differential Lock Pedal Hazard Light SwitchEngine Coolant Temperature Light Battery Indicator LightParking Brake Indicator Light PTO Indicator LightOperation Safety Interlock SystemRollover Protective Structure Rops Fueling the TractorStarting the Engine NEW Tractor BREAK-IN ProceduresCold Weather Starting below 14 F Using Jumper Cables to Start EngineStopping the Engine Driving the TractorUsing the Forward and Reverse Pedals Using the HI/LO Range Shift LeverLOW Using the Differential Lock Pedal Using the 4WD Shift LeverDriving on Slopes Using the PTO Reverse Override Switch Using the Hydraulic Lift LeverEngaging the PTO LightingUsing the Three Point Hitch Using the TOP Link Retainer HookHazard Lights Removing the Rear PTO CoverTractor Weighting Using the Hitch PlateFront Weights Weighting the Rear of the TractorAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting the Brakes Maintenance Lubrication TableGeneral Information Lubrication and Maintenance Chart Illustration Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentCharging the Battery Battery RemovalBattery Maintenance Battery StorageHead Light Bulb Replacement Hazard Bulb ReplacementServicing Electrical System Instrument Panel Fuses Accessing the Fuse CenterRelays Main FuseHydraulic System Filter Part No Checking TRANSMISSION/HYDRAULIC System OIL LevelChanging the Hydro Transmission and Hydraulic System OIL Changing Hydraulic System FilterCheck Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Drive Shaft Lubrication of FWD Drive ShaftWheel LUG NUT Torque Maintenance of the Rollover Protective Structure Rops Tire MaintenanceRemoving the Tractor from Storage Tractor StorageDaihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceIgnition System Cleaning the Radiator SCREEN/RADIATOR Engine Maintenance Cleaning the EngineChecking Engine OIL Level Adding Engine OILChanging the Engine OIL and Filter Checking Engine Coolant Level Inspection of Cooling System HosesChanging the Engine Coolant Changing the AIR Cleaner Servicing the Fuel Filter Draining The Fuel FilterChanging The Fuel Filter Specifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Model Number Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

5234D specifications

The Cub Cadet 5234D is a versatile and powerful compact tractor designed for a variety of landscaping and agricultural tasks. Known for its durability and efficiency, this model is ideal for homeowners with large yards, small farm operators, or landscapers requiring reliable performance. With a robust 34 horsepower engine, the 5234D boasts the power needed to tackle tough jobs, from mowing to hauling heavy loads.

One of the standout features of the Cub Cadet 5234D is its hydrostatic transmission. This technology offers seamless speed control, allowing operators to adjust their speed without needing to shift gears. This makes it particularly user-friendly for individuals of all skill levels, fostering a smooth driving experience whether traversing flat terrain or navigating inclines.

The tractor is equipped with a 4-wheel drive system, providing enhanced traction and stability on various surfaces. This feature is essential when working on challenging landscapes, muddy fields, or hilly areas, ensuring that the machine remains stable and maintains consistent power delivery.

Another significant characteristic of the Cub Cadet 5234D is its heavy-duty build quality. The frame and body are engineered to withstand the rigors of daily use, making it a reliable choice for both homeowners and professionals. With a tight turning radius, this compact tractor excels in maneuverability, allowing users to work effortlessly in tight spaces or around obstacles.

The 5234D also includes a convenient mid-mount mower deck, which can effectively cut grass while the operator focuses on other tasks. Its adjustable cutting height allows for customized lawn maintenance, accommodating different grass types and seasonal changes.

Comfort is also a priority with this model, as it features an ergonomic seating arrangement. The operator’s station is designed to minimize fatigue during extended use, with easy-to-reach controls and adequate legroom.

Safety is paramount, with the inclusion of safety features such as roll-over protection structures and easy-to-access brakes.

In summary, the Cub Cadet 5234D combines power, maneuverability, and comfort, making it an exceptional choice for those in need of a reliable compact tractor. Its blend of advanced technology and user-friendly design ensures it can handle a range of tasks efficiently, allowing users to maximize productivity while enjoying their work.