Cub Cadet 5234D manual Adjusting the Brakes

Page 24

ADJUSTING THE BRAKES

The tractor brakes are adjusted at the factory and should experience minimal wear if the tractor is operated normally. However, all brake pads are subject to wear and at some point the brake linkage may have to be adjusted.

Check the brakes as follows:

•Place the tractor on a level surface. Stop the tractor engine.

•From beneath the RH running board, remove the internal cotter pin to disengage the brake rod ferrule from the brake pedal. Position the brake rod to make certain there is no pull on the brake actuator arm. See Figure 30.

•From the rear of the tractor, use a feeler gauge to measure the gap between the outer brake

puck and the brake disc. The gap should mea- sure between .012 and .015". See Figure 30.

•If the gap is greater than .015", tighten the hex nut on the brake assembly until the gap is within the tolerance.

•Position the ferrule to align with the hole in the brake pedal. If the ferrule does not align with the hole, loosen the jam nut by turning it away from the ferrule

•Adjust the ferrule on the brake rod to align with the brake pedal hole, then tighten the jam nut against the ferrule.

•Insert the ferrule in the brake pedal and secure with the internal cotter pin.

•Repeat the previous steps to check and, if necessary, adjust the LH brake assembly.

INTERNAL

COTTER PIN

JAM NUT

FERRULE

RH BRAKE ROD

GAUGE

.012 - .015" BRAKE ACTUATOR

ARM

BRAKE PEDAL

BRAKE DISC

HEX NUT

Figure 30

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Rops Information PlateImportant Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops ServiceChildren Operating the PTOPage Safety Labels Battery Warning Label Located Under HoodFAN Warning Label Located on Each Side of Radiator PTO Warning Label Located on Rear PTO ShieldControls and Features PTO Switch Ignition SwitchSteering Wheel Throttle HandleSeat Adjustment Lever PTO Reverse Override SwitchHand Holds Transmission 4WD Shift LeverDifferential Lock Pedal Hazard Light Switch Headlight SwitchBattery Indicator Light Engine Coolant Temperature LightParking Brake Indicator Light PTO Indicator LightSafety Interlock System OperationRollover Protective Structure Rops Fueling the TractorNEW Tractor BREAK-IN Procedures Starting the EngineUsing Jumper Cables to Start Engine Cold Weather Starting below 14 FStopping the Engine Driving the TractorUsing the Forward and Reverse Pedals Using the HI/LO Range Shift LeverLOW Using the Differential Lock Pedal Using the 4WD Shift LeverDriving on Slopes Using the Hydraulic Lift Lever Using the PTO Reverse Override SwitchEngaging the PTO LightingUsing the TOP Link Retainer Hook Using the Three Point HitchHazard Lights Removing the Rear PTO CoverUsing the Hitch Plate Tractor WeightingFront Weights Weighting the Rear of the TractorAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Maintenance Lubrication TableGeneral Information Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Charging the BatteryBattery Maintenance Battery StorageHead Light Bulb Replacement Hazard Bulb ReplacementServicing Electrical System Accessing the Fuse Center Instrument Panel FusesRelays Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Hydraulic System Filter Part NoChanging Hydraulic System Filter Changing the Hydro Transmission and Hydraulic System OILCheck Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Drive Shaft Lubrication of FWD Drive ShaftWheel LUG NUT Torque Tire Maintenance Maintenance of the Rollover Protective Structure RopsTractor Storage Removing the Tractor from StorageEngine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageIgnition System Engine Maintenance Cleaning the Engine Cleaning the Radiator SCREEN/RADIATORChecking Engine OIL Level Adding Engine OILChanging the Engine OIL and Filter Checking Engine Coolant Level Inspection of Cooling System HosesChanging the Engine Coolant Changing the AIR Cleaner Servicing the Fuel Filter Draining The Fuel FilterChanging The Fuel Filter Specifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

5234D specifications

The Cub Cadet 5234D is a versatile and powerful compact tractor designed for a variety of landscaping and agricultural tasks. Known for its durability and efficiency, this model is ideal for homeowners with large yards, small farm operators, or landscapers requiring reliable performance. With a robust 34 horsepower engine, the 5234D boasts the power needed to tackle tough jobs, from mowing to hauling heavy loads.

One of the standout features of the Cub Cadet 5234D is its hydrostatic transmission. This technology offers seamless speed control, allowing operators to adjust their speed without needing to shift gears. This makes it particularly user-friendly for individuals of all skill levels, fostering a smooth driving experience whether traversing flat terrain or navigating inclines.

The tractor is equipped with a 4-wheel drive system, providing enhanced traction and stability on various surfaces. This feature is essential when working on challenging landscapes, muddy fields, or hilly areas, ensuring that the machine remains stable and maintains consistent power delivery.

Another significant characteristic of the Cub Cadet 5234D is its heavy-duty build quality. The frame and body are engineered to withstand the rigors of daily use, making it a reliable choice for both homeowners and professionals. With a tight turning radius, this compact tractor excels in maneuverability, allowing users to work effortlessly in tight spaces or around obstacles.

The 5234D also includes a convenient mid-mount mower deck, which can effectively cut grass while the operator focuses on other tasks. Its adjustable cutting height allows for customized lawn maintenance, accommodating different grass types and seasonal changes.

Comfort is also a priority with this model, as it features an ergonomic seating arrangement. The operator’s station is designed to minimize fatigue during extended use, with easy-to-reach controls and adequate legroom.

Safety is paramount, with the inclusion of safety features such as roll-over protection structures and easy-to-access brakes.

In summary, the Cub Cadet 5234D combines power, maneuverability, and comfort, making it an exceptional choice for those in need of a reliable compact tractor. Its blend of advanced technology and user-friendly design ensures it can handle a range of tasks efficiently, allowing users to maximize productivity while enjoying their work.
Top Page Image Contents