Cub Cadet 5234D manual Changing Hydraulic System Filter

Page 33

•Remove the old hydrostatic filter by turning it counterclockwise, and immediately replace with the new filter. Turn the filter clockwise by hand until the gasket contacts the filter base; then tighten the filter an additional 1/2 to 3/4 turn.

•Clean any residual oil from the top of the transmission.

Changing Hydraulic System Filter

The hydro transmission oil filter should be changed after the first 25 of tractor operation, and after every 200 hours operation.

•Stop the tractor engine and lower the mower deck or any other hydraulically lifted implement to the ground. NOTE: To improve access to the hydraulic system filter, the mower deck may be removed from the tractor.

•Clean the area around the hydraulic system oil filter to prevent debris from entering the trans- mission housing.

•Position a suitable container below the hydrau- lic system filter. Refer to Figure 43

NOTE (25 Hour Break-In Filter Change Only): A large volume of oil may drain from the transmission when changing the hydraulic system oil filter. If collected in a clean container and kept free of contamination and debris, this oil may be reused in the transmission/ hydraulic system.

HYDRAULIC SYSTEM

OIL FILTER

TRANSMISSION

DRAIN PLUG

Figure 43

•Apply a light coating of clean transmission oil to the gasket of the new hydraulic system filter.

NOTE: If performing the 25 hour break-in filter change, install the new filter as quickly as possible to minimize the amount of oil that drains from the transmission.

•Remove the old hydraulic system filter by turn- ing it counterclockwise.

•If performing the 25 hour filter change, install the new filter immediately. If performing the 200 hour filter change, clean the oil filter base.

•Install the new filter. Turn the filter clockwise, by hand, until the gasket contacts the filter base on the transmission housing; then tighten the filter an additional 1/2 to 3/4 turn.

•Clean the area around the transmission fill plug to prevent debris from entering the transmis- sion (Refer to Figure 41) and remove the plug.

•Following the instructions previously provided in CHECKING TRANSMISSION/HYDRAULIC SYSTEM OIL LEVEL, refill the transmission with the clean oil and/or new hydraulic oil.

•Reinsert the oil fill plug into the transmission housing and turn clockwise until tight.

•Start the engine and allow it to run for a few minutes. Shut the engine off, then check for leaks and recheck the oil level in the transmis- sion housing.

CHANGING THE HYDRO TRANSMISSION AND HYDRAULIC SYSTEM OIL

Change the hydrostatic transmission/hydraulic system oil after every 200 hours of operation. The dry capacity of the transmission/hydraulic system is approximately 20 quarts.

Change the transmission/hydraulic system oil as follows:

•Operate the tractor for a short period to warm the oil to the normal operating temperature. Place the tractor on a level surface and engage the parking brake.

•Stop the tractor engine and lower the mower deck or any other hydraulically lifted implement to the ground. NOTE: To improve access to the drain plug and hydraulic system filter, the mower deck may be removed from the tractor.

•Clean the area around the transmission drain plug and the oil fill plug to prevent debris from entering the transmission. Refer to Figure 41 and Figure 43.

•Place a suitable container(s) beneath the front of the transmission housing.

•Remove the oil fill plug to help vent the trans- mission, then remove the drain plug and allow the transmission oil to drain into the con- tainer(s). Reinstall the drain plug after draining the oil. Refer to Figure 41 and Figure 43.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTable of Contents Calling Service InformationTo the Owner Rops Information Plate Recording Model and Serial Number InformationGeneral Operation Important Safe Operation PracticesDo not Slope OperationService Safety Frame RopsChildren Operating the PTOPage Battery Warning Label Located Under Hood Safety LabelsFAN Warning Label Located on Each Side of Radiator PTO Warning Label Located on Rear PTO ShieldControls and Features Ignition Switch PTO SwitchSteering Wheel Throttle HandlePTO Reverse Override Switch Seat Adjustment LeverHand Holds Transmission 4WD Shift LeverHeadlight Switch Differential Lock Pedal Hazard Light SwitchEngine Coolant Temperature Light Battery Indicator LightParking Brake Indicator Light PTO Indicator LightOperation Safety Interlock SystemRollover Protective Structure Rops Fueling the TractorStarting the Engine NEW Tractor BREAK-IN ProceduresCold Weather Starting below 14 F Using Jumper Cables to Start EngineStopping the Engine Driving the TractorUsing the Forward and Reverse Pedals Using the HI/LO Range Shift LeverLOW Using the Differential Lock Pedal Using the 4WD Shift LeverDriving on Slopes Using the PTO Reverse Override Switch Using the Hydraulic Lift LeverEngaging the PTO LightingUsing the Three Point Hitch Using the TOP Link Retainer HookHazard Lights Removing the Rear PTO CoverTractor Weighting Using the Hitch PlateFront Weights Weighting the Rear of the TractorAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting the Brakes Maintenance Lubrication TableGeneral Information Lubrication and Maintenance Chart Illustration Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentCharging the Battery Battery RemovalBattery Maintenance Battery StorageHead Light Bulb Replacement Hazard Bulb ReplacementServicing Electrical System Instrument Panel Fuses Accessing the Fuse CenterRelays Main FuseHydraulic System Filter Part No Checking TRANSMISSION/HYDRAULIC System OIL LevelChanging the Hydro Transmission and Hydraulic System OIL Changing Hydraulic System FilterCheck Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Drive Shaft Lubrication of FWD Drive ShaftWheel LUG NUT Torque Maintenance of the Rollover Protective Structure Rops Tire MaintenanceRemoving the Tractor from Storage Tractor StorageDaihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceIgnition System Cleaning the Radiator SCREEN/RADIATOR Engine Maintenance Cleaning the EngineChecking Engine OIL Level Adding Engine OILChanging the Engine OIL and Filter Checking Engine Coolant Level Inspection of Cooling System HosesChanging the Engine Coolant Changing the AIR Cleaner Servicing the Fuel Filter Draining The Fuel FilterChanging The Fuel Filter Specifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Model Number Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

5234D specifications

The Cub Cadet 5234D is a versatile and powerful compact tractor designed for a variety of landscaping and agricultural tasks. Known for its durability and efficiency, this model is ideal for homeowners with large yards, small farm operators, or landscapers requiring reliable performance. With a robust 34 horsepower engine, the 5234D boasts the power needed to tackle tough jobs, from mowing to hauling heavy loads.

One of the standout features of the Cub Cadet 5234D is its hydrostatic transmission. This technology offers seamless speed control, allowing operators to adjust their speed without needing to shift gears. This makes it particularly user-friendly for individuals of all skill levels, fostering a smooth driving experience whether traversing flat terrain or navigating inclines.

The tractor is equipped with a 4-wheel drive system, providing enhanced traction and stability on various surfaces. This feature is essential when working on challenging landscapes, muddy fields, or hilly areas, ensuring that the machine remains stable and maintains consistent power delivery.

Another significant characteristic of the Cub Cadet 5234D is its heavy-duty build quality. The frame and body are engineered to withstand the rigors of daily use, making it a reliable choice for both homeowners and professionals. With a tight turning radius, this compact tractor excels in maneuverability, allowing users to work effortlessly in tight spaces or around obstacles.

The 5234D also includes a convenient mid-mount mower deck, which can effectively cut grass while the operator focuses on other tasks. Its adjustable cutting height allows for customized lawn maintenance, accommodating different grass types and seasonal changes.

Comfort is also a priority with this model, as it features an ergonomic seating arrangement. The operator’s station is designed to minimize fatigue during extended use, with easy-to-reach controls and adequate legroom.

Safety is paramount, with the inclusion of safety features such as roll-over protection structures and easy-to-access brakes.

In summary, the Cub Cadet 5234D combines power, maneuverability, and comfort, making it an exceptional choice for those in need of a reliable compact tractor. Its blend of advanced technology and user-friendly design ensures it can handle a range of tasks efficiently, allowing users to maximize productivity while enjoying their work.
Top Page Image Contents