Craftsman 247.77099 operating instructions Attaching the BAG, Attaching the Blower Chute

Page 8

ATTACHING THE BAG

•Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod. See Figure 6.

Bag Clip
Bag Handle
Strap
Stud
Locking
Rod
Bag/Chute
Switch	Stud
Button
Front
Tab

Figure 6

•Slip bag over the rim of the discharge opening and release locking rod to secure bag in place.

•Snap bag clip to the top of the lower handle.

•Place the lower straps on the bag over the top of lower handle, hooking them on the studs.

NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on bag handle when securing the bag or engine will not start.

ATTACHING THE BLOWER CHUTE

NOTE: The bag must be removed before installing the blower chute.

•Grasp blower chute with one hand and slide lock- ing rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod.

See Figure 7.

•Slip blower chute over rim of discharge opening and release locking rod to secure chute in place.

•Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment in the ADJUSTMENT section on page 11.

NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on the blower chute or engine will not start.

Front		Blower
Front		Chute
Tab		Chute
Tab
		Bag/Chute
		Switch
		Button
		Front
		Tab Locking
	Locking	Rod
	Locking
	Rod
	Engine Removed
	For Clarity

Figure 7

8

Image 8

Contents Power Propelled Yard Vacuum Table of Contents WarrantyPreparation SafetyTraining Maintenance and Storage OperationRepair Protection Agreement Disconnecting Spark Plug AssemblyOpening Carton Removing Unit from CartonAttaching the Hose Assembly Attaching the HandleAttaching the BAG Attaching the Blower ChuteNozzle Height Adjustment Lever Chipper ChuteDrive Control Speed ControlGAS and OIL FILL-UP Nozzle Height Adjustment To Stop EngineTo Start Engine To Empty BAGUsing the Nozzle Vacuum Using the Hose AssemblyClean Equipment General RecommendationsLubrication Check Engine OILService Spark Plug Service AIR CleanerService Muffler Clean EngineCarburetor Adjustment Service and AdjustmentsSharpening or Replacing Chipper Blade Engine SpeedRemoving the Flail Screen Housing Screws Nozzle Lower Housing Yard Vacuum StorageTroubleshooting Problem Possible Causes Corrective ActionParts List Part Description Sears Craftsman 6.5 H.P. Yard Vacuum Model 20 -2293A Nozzle 781-1064 Label KIT Carburetor 187 608398188†† Valve-Needle/Seat Part Description Sears Emission Control Defects Warranty Coverage Page Page Esta garantía no cubre ÍndiceGarantía Seguridad CapacitaciónPreparación Funcionamiento Mantenimiento Y Almacenamiento Acuerdo DE Protección Para Reparaciones Apertura DE LA Caja DE Cartón Cómo Sacar LA Unidad DE LA CajaDesconexión DE LA Bujía MontajeMontaje DE LA Manija Instalación del montaje de la mangueraMontaje DE LA Bolsa Instalar EL Canal DE SopladoFuncionamiento Montaje de la manguera Manija de la mangueraCanal de soplado PicoDescarga DE LA Bolsa Para Detener EL MotorPara Encender EL Motor Uso del pico de la aspiradora Lubricación Limpieza DEL EquipoCompruebe EL Aceite DEL Motor MantenimientoCómo Vaciar EL Aceite Servicio DEL Filtro DE AireServicio a LA Bujía Servicio AL SilenciadorServicio Y Ajustes Ajuste DEL Cable DEL Control DE TransmisiónAjuste DEL Carburador Velocidad DEL Motor Extracción DE LA Pantalla DE DesgranadoTornillos De la caja Del pico De la caja inferior Aspiradora para patios AlmacenamientoSolución DE Problemas Problema Causas posibles Acciones correctivasEsta página se aplica sólo en EE.UU. y Canadá Get it fixed, at your home or ours