Billy Goat KV650SPH Maintenance, Impeller Removal, Drive Chain Replacement and Alignment

Page 12

KVSP/TKVSP Owner’s Manual

MAINTENANCE

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation

Every Use (daily)

Every 5 hrs (daily)

Every 25 Hours

 

 

 

 

Inspect for loose, worn or damaged parts.

 

z

 

 

 

 

 

Clean Debris bag

z

 

 

 

 

 

 

Check bag strap tightness

z

 

 

 

 

 

 

Engine (See Engine Manual)

 

 

 

 

 

 

 

Check for excessive vibration

 

z

 

 

 

 

 

IMPELLER REMOVAL

1.Wait for engine to cool and disconnect spark plug.

2.Drain fuel and oil from the engine.

3.Remove bag, quick release and upper handle. Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles.

4.Remove the transmission cover, idler pulley, transmission and the belt from the transmission.

5.Remove the transmission plate and the housing top plate by removing bolts around outside of housing.

6.Leaving engine fastened to top plate; turn it upside down so the impeller is on top.

7.Remove impeller bolt and lock washer.

8.Lift impeller upward. If impeller slides freely, proceed to (step 10).

9.If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the shaft, remove impeller from shaft. Using a penetrating oil can help loosen a stuck impeller.

10.Using a new impeller bolt, lockwasher, and washer, reinstall new impeller in reverse order.

11.Tighten impeller bolt. Torque impeller bolt to 33-38 Ft. Lbs. (44-51 N.m) (see item 45 on page 15).

12.Reinstall engine onto housing in reverse order of removal make sure the belt is inside the two fingers on the belt plate and that the belt is on the transmission pulley before securing the transmission.

13.Gas and oil.

14.Reconnect spark plug wire.

DRIVE CHAIN REPLACEMENT AND ALIGNMENT

1.Wait for engine to cool and disconnect spark plug.

2.To replace a chain, first prop up the rear of the machine with small blocks to get the rear wheels off of the ground.

3.Remove the transmission cover, and the belt from the transmission.

4.Remove the bolts on both sides of the transmission holding the flange bearings; this should give enough slack to slip the chain off.

4.Replace the old chain with a new one.

5.Once the chain is on, put the bolts back into the flange bearings and tighten.

6.Finally, make sure the wheels rotate freely. If not, loosen the bearings and shift them to get the chain running straight up and down.

7.Reassemble the transmission components removed in steps 1-3 in reverse order.

Part No 891058

12

Form No F072508B

Image 12
Contents Billy Goat KV Vacuum KV600SP, KV650SPH, TKV650SPHContents About this ManualSpecifications Serial Plate DataGeneral Safety Instructions and Symbols Form No F072508B Sound Vibration DataIntended USE Honda Briggs & Stratton Instruction LabelsEngine Labels Packing Checklist AssemblyParts BAG Literature Assy Operation StartingIf Your Unit Fails to Start Handling & TransportingVacuuming Operation Debris BAGCompost MulchMaintenance Drive Chain Replacement and AlignmentImpeller Removal Do not Adjust While the Machine is Running Belt Tension AdjustmentBelt Replacement Chipper Blade Removal and Sharpening TKV only Chipper blades are normal replaceable wear itemsTroubleshooting Warranty Claim ProcedureParts Drawing KVSP/TKVSP Parts List KVSP/TKVSP Washer Lock 3/8 ST MEDMaintenance Record Form No F072508B Form No F072508B

TKV650SPH, KV650SPH specifications

The Billy Goat TKV650SPH and KV650SPH are exceptional outdoor power tools designed to meet the needs of both professionals and homeowners. Known for their impressive capabilities, these rugged blowers are designed to tackle heavy debris management with ease.

One of the standout features of the TKV650SPH and KV650SPH is their powerful 650cc engine. This engine delivers superb performance, ensuring consistent airflow and suction, which is ideal for clearing leaves, grass clippings, and other debris. The high-performance engine not only enhances operational efficiency but also allows users to complete their tasks in a fraction of the time compared to underpowered alternatives.

Both models are designed with a robust chassis that provides excellent stability and durability. This is especially important for those who work in challenging conditions. The TKV650SPH, in particular, is equipped with a self-propelling feature that allows for easier maneuverability across various terrains, reducing user fatigue during extended use.

An important technology incorporated into these models is the variable speed control. This feature allows users to easily adjust the blower's airspeed to suit the task at hand. Whether you need to delicately clear debris from flower beds or generate more power for larger areas, the adjustable speed settings provide ultimate versatility.

Moreover, the TKV650SPH and KV650SPH models are equipped with a 3-in-1 function that includes vacuuming, blowing, and shredding capabilities. This multi-functionality enables users to efficiently switch between tasks, minimizing the need for additional equipment.

The shredding capability is particularly noteworthy, as it reduces the volume of collected debris, making disposal easier and more efficient. Additionally, the design of the collection bag is optimized for maximum capacity, ensuring fewer interruptions during operation.

Comfort is also a priority in the design of these blowers. They feature ergonomic handles that improve grip and reduce strain during use. The lightweight construction further enhances ease of handling, making these blowers an excellent choice for prolonged use.

In summary, the Billy Goat TKV650SPH and KV650SPH represent the pinnacle of outdoor blowers, combining power, versatility, and user-friendly features. Whether used for professional landscaping or residential yard maintenance, these models stand out for their ability to handle diverse tasks efficiently and effectively. As such, they are an investment worth considering for anyone in need of robust yard management tools.