Homelite HP3127S Unpacking, Packing List, Attaching the Wheel Assembly, Hitch PIN Axle Washer

Page 9

ASSEMBLY

UNPACKING

This product requires assembly.

Carefully cut the box down the sides then remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included.

NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

Remove and discard the clear cap securing the operator’s manual bag to the pump breather tube.

Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

Do not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

If any parts are damaged or missing, please call 1-866-260-8280 for assistance.

PACKING LIST

Pressure Washer

30 ft. High Pressure Hose Spray Wand Assembly (upper) Assist Handle Assembly Spray Wand Extension (lower) Quick-Connect Nozzle (5) Nozzle Cleaning Tool Resting Foot

Axle Assembly (2) Wheel (2) Washer (2) Hardware Bag

4-Cycle Engine Oil (10W-30) Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this tool until the parts are replaced. Failure to heed this warn- ing could result in possible serious personal injury.

WARNING:

Do not attempt to modify this tool or create accesso- ries not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts.

NOTE: Do not start the pressure washer until the engine has been filled with oil and all hoses are connected. Running this machine without oil will damage the engine while running it without water will damage the high pressure pump.

ATTACHING THE WHEEL ASSEMBLY

See Figure 2.

To attach the wheels to the pressure washer base:

Locate the axle assembly; remove the hitch pin from the axle.

Slip the axle into the wheel hole and slide the washer onto the axle.

Lift the machine and slide the axle/wheel/washer combination into the wheel mounting hole in the machine base as shown.

Push the hitch pin into the hole on the end of the axle to secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until the center of the pin rests on top of the axle.

Repeat with the second wheel assembly.

NOTE: It is important to always maintain proper air pressure in both wheels.

HITCH PIN

AXLE

WASHER

Fig. 2

Page 9

Image 9
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions Before Using this Product Important Safety InstructionsSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsService Product Specifications Features Attaching the Wheel Assembly AssemblyUnpacking Packing ListAttaching the Resting Foot Connecting High Pressure Hose to Spray Wand AssemblyAssembling the Spray Wand Attaching Injection HoseAdding OIL to the Engine Adding Gasoline to the Fuel TankFuel CAP Funnel Connecting the High Pressure Hose to Pump To connect the garden hose to the machineScreen Operation ApplicationsSTARTING/STOPPING the Pressure Washer Selecting the Right QUICK-CONNECT Nozzle for the JOB Using the Spray Wand TriggerStoring the Pressure Washer Moving the Pressure WasherWashing with Detergent Rinsing with the Pressure WasherMaintenance Cleaning the AIR FilterGeneral Maintenance Nozzle Maintenance Cleaning Fuel CUPPump Maintenance Changing the OILPreparing for USE After Storage Periodic Maintenance Schedule TableProblem Cause Solution TroubleshootingPage Warranty General Emissions Warranty Coverage Parts Covered Under the California Emissions Warranty Warranty Periods Limited ROBIN/SUBARU Engine WarrantyLimited NON Engine Warranty Statement California Proposition Service