Delta D29382 instruction manual Trouble Shooting Guide, Problem Cause Correction

Page 16

TROUBLE SHOOTING GUIDE

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Motor will not

Pressure washer not plugged in.

 

Plug in pressure washer.

 

 

 

“RESET” button on GFCI not

 

Push “RESET” button.

start and there

 

is no humming

pushed.

 

 

sound

 

 

 

Circuit breaker has tripped or fuse

 

Reset breaker or replace fuse.

 

is blown.

 

 

 

 

 

 

Power source

Too much load already on circuit.

 

Reduce load on circuit.

circuit

 

 

Try another 15 amp circuit.

continues to

 

 

 

 

 

Using an extension cord.

 

DO NOT use extension cords.

trip or blow

 

fuses

 

 

 

 

 

 

 

Motor hums but

Using an extension cord.

 

DO NOT use extension cords.

will not start

 

 

 

 

Supply voltage below required

 

Check the voltage of the main

 

minimum.

 

supply line.

 

 

 

 

No or low

Low water supply.

 

Water supply must be at least 5

pressure

 

 

GPM @ 20 psi.

 

 

 

 

 

High pressure hose is too long.

 

Use high pressure hose under

 

 

 

100 feet.

 

 

 

 

 

Worn nozzle.

 

Replace nozzle.

 

 

 

 

Excess noise

Restricted, insufficient water

 

Check supply hose, faucet, and

supply, or air in the water line.

 

inlet screen.

 

 

 

Water temperature is too high.

 

Do not use water from a hot

 

 

 

water source, use water only from

 

 

 

a cold water faucet.

 

 

 

 

Pressure

Water leak in high pressure fittings,

 

Replace hose or gun. If problem

fluctuates with-

 

hose, or gun.

 

continues take to authorized

out opening gun

 

 

 

service center.

 

 

 

 

 

 

 

GFCI switch

Circuit breaker has tripped or fuse

 

Reset breaker or replace fuse. If

indicator light

is blown.

 

indicator light still does not

does not appear

 

 

appear have receptacle checked

after depressed

 

 

by a qualified electrician.

 

 

 

 

GFCI test fails

Circuit breaker has tripped or fuse

 

Reset breaker or replace fuse. If

 

is blown.

 

indicator light still does not

 

 

 

appear have receptacle checked

 

 

 

by a qualified electrician.

 

 

 

 

Unit does not

Nozzle clogged

 

Clean nozzle, if unit still does not

maintain steady

 

 

maintain steady water pressure,

water pressure

 

 

turn unit off and contact customer

 

 

 

service at 1-866-422-4286

 

 

 

 

Unit continues

Nozzle clogged

 

Clean nozzle, if unit still does not

to trip GFCI

 

 

maintain steady water pressure,

switch

 

 

turn unit off and contact customer

 

 

 

service at 1-866-422-4286

 

 

 

 

D29382

16- ENG

Image 16
Contents Instruction Anum AL Safety Guidelines Definitions Risk of Electrical ShockRisk of Explosion or Fire Risk to BreathingRisk of Unsafe Operation Risk of HOT SurfacesGround Fault Circuit Interrupter Protection Grounding InstructionsExtension Cords Risk of Injury from SprayCarton Contents Assembly Instructions Operating Instructions ON-OFFHOW to USE Spray Wand HOW to USE the Cleaning Solution Application UnitD29382 ENG Read and Understand ALL Warnings Before Starting Unit Before StartingStarting Your Pressure Washer Maintenance Recommended CleaningShutting Down Your Pressure Washer Suction FilterD29382 ENG When Freezing Temperatures are Expected StorageTrouble Shooting Guide Problem Cause CorrectionENG D29382 Warranty Responsibility of Original Purchaser initial User