LightSpeed Technologies CAT 860 user manual LT-71 Charging

Page 38

5. Warranty, Safety

& Specifications

 

 

 

4. Troubleshooting

 

 

 

 

3. Optional

Accessories

 

 

 

2. Setup & Use

 

 

 

1. Overview

 

 

LT-71: Charging

1.Ensure that the LT-71 is turned OFF.

2.Make sure the cradle charger

is plugged into a wall outlet. Connect one end of the charging cable into the jack labeled CHARGER on the side of the LT-71 and plug the other end into the charging jack on the rear of the REDMIKE cradle charger. The LT-71’s rechargeable batteries are factory installed. The LED on the front of the LT-71 will glow RED when charging.

3.Leave the LT-71 plugged in overnight (8–10 hrs.) to obtain a full charge.

NOTE: If the system was purchased without a REDMIKE or REDMIKE VC, the LT-71 will utilize a charging cable. Simply connect the charging cables to the jacks labeled CHARGER on the back of the amplifier and connect the opposite ends to the jacks on the back of the cradle charger.

Front Panel

RS-232

 

 

1

Control Select

2

 

+ -

- +

RS-232 IN

 

 

 

 

LT-71: Initial Set-up

Once the LT-71 is charged, follow these steps to set it up for use.

1. Turn the CAT 860 power switch to the ON position. The RED LED on the switch will glow.

2. Turn on the LT-71 and set the

operating channel to “B”.

3.Slip the LT-71 with lanyard around the neck and position the top of the microphone just below the

collarbone. NOTE: Positioning

 

of the LT-71 is critical for proper

 

volume adjustment.

LT-71

4. While speaking in a normal voice

slowly increase the volume for Channel B on the CAT 860 until your voice is barely audible.

REMEMBER: This equipment supplements the user’s voice so they are able to speak in a conversational tone. Having the volume set too high will result in feedback and listener fatigue.

3. Optional5. Warranty, Safety 1. Overview2. Setup & Use4. Troubleshooting Accessories& Specifications

74

75

Page 37 Page 39
Image 38
Page 37 Page 39
Contents CAT Table of Contents Table of Contents CONT’D Important Safety Instructions System Components and Unpacking Standard configuration of the CAT 860 will containSpeakers and Speaker Wire Standard ComponentsOptional equipment which may be part of your CAT 860 system Optional ComponentsFront Panel Controls Optional ComponentsRear Panel Controls Infrared SENSOR/RECEIVER ISR ConnectionsOverview SET-UP & USE Location of the AmplifierIR SENSOR/RECEIVER ISR Installation Clip connects to t-bar on ceiling Release Bar5A. Connect the Power Supply Installation of Amplifier WALL- Mount BracketSpeaker Installation 5B. ISR Connection5D. Audio Input Connections 5C. Speaker ConnectionsAudio Integration One Possible Set-upGreen Setup and Operation of RedmikeCharging the Redmike Audio Equalization of the CAT Output to Personal Assistive Listening Device ALDAudio Output Pagefirst Priority MuteAudio Input Command Structure RS-232 Data SignalsConnector Signal Wiring Serial Interface ProtocolRS-232 Serial Interface Summary of command and response transactionsSummary of command and response transactions Cont’d Programming CONT’DGeneral Format for Query Command Exchange Control Character Hex Value and DefinitionCMD Basic Command SET for Audio Switcher OperationsBasic Command SET for Audio Switcher Operations CONT’D 0xE4 Command Packet Mavs Mute AUDIO/VIDEO Sources CommandUN-MUTE Enabled AUDIO/VIDEO Source Command Uavs0xE8 Command Packet Tmmi Toggle Mute for Microphone Audio Inputs CommandQuery Enabled AUDIO/VIDEO Source Command QEAV?QVAV? Query Absolute Volume AUDIO/VIDEO Source CommandQuery Absolute Volume Microphone Audio Input Command QVMI?QMAV? Query Mute for AUDIO/VIDEO Source CommandQuery Mute for Microphone Audio Inputs Command QMMI?Query Selected Audio Input Command CMD Advanced Command SET for Audio Mixer OperationsAdvanced Command SET for Audio Mixer Operations CONT’D AICH?Param #1 Param #20x95 Command Packet Response Packet SET Absolute Volume for Selected Audio Input CommandQuery Absolute Volume for Selected Audio Input Command AIAV?AOCH? 0xA1 Command Packet Select Audio Output CommandQuery Selected Audio Output Command SET Absolute Volume for Selected Audio Output Command 0xB1 Command Packet Audio Input Functions for the Infrared Source Group Cont’d 0xB5 Command Packet Response Packet SET Absolute Volume for Selected Infrared Input CommandQuery Absolute Volume for Selected Infrared Input Command IIAV?Input Muting Functions Group Cont’d Mute Selected Audio Input CommandUN-MUTE Selected Audio Input Command COMPUTER, & AUX0xC0 Command Packet Response Packet Symbol Value Audio Input FunctionsSymbol Value CMD Hex Param Value DefinitionPing Power /MUTE ButtonHex Param Value Definition AUDIO/MICROPHONE InputRedmike VC Charging LT-71 Charging Channel Select Switch Power SwitchPOWER/CHARGE Indicator Audio Input plug a laptopInitial SET-UP Optional IR Media Connector Redmike Share Initial Set-upALL Problems Most Problems are related to low battery power Common Problems and SolutionsOther Optional Accessories FIVE-YEAR Limited Warranty Tips to Obtain Optimum Audio PerformanceSafety Warnings and Certifications Risk of Electric Shock do not OpenSystem Specifications Overall SpecificationsLightspeed Technologies

CAT 860 specifications

LightSpeed Technologies has made significant strides in the field of educational technology with its innovative product, the CAT 860. This advanced audio distribution system is designed to enhance learning environments by ensuring that every student can hear their teacher clearly, regardless of classroom size or layout. The CAT 860 is particularly valuable in diverse educational settings, from traditional classrooms to modern digital learning environments.

One of the standout features of the CAT 860 is its powerful amplification capabilities. The system is equipped with a robust amplifier that delivers crystal-clear sound, offering a more engaging experience for students. This clarity not only enhances comprehension but also reduces fatigue during prolonged listening sessions. The CAT 860 uses digital signal processing to eliminate background noise and offers a full-range audio experience without distortion, which is critical in maintaining student attention.

Another key characteristic of the CAT 860 is its flexibility in terms of connectivity. It supports various input sources, including microphones, audio devices, and streaming services. This versatility makes it easier for teachers to incorporate multimedia resources into their lessons, fostering a more dynamic and interactive learning process. Moreover, the system can connect wirelessly to other devices, allowing for seamless integration into existing educational technology infrastructure.

Additionally, the CAT 860 is user-friendly, featuring a simple interface that allows teachers to quickly adjust volume levels and select audio sources without needing extensive technical training. This ease of use encourages teachers to utilize the system more frequently, which in turn maximizes the benefits of enhanced audio in the classroom.

In terms of design, the CAT 860 is compact and aesthetically pleasing, making it a suitable addition to any classroom environment. Its modern design ensures that it blends seamlessly with other teaching aids and equipment, maintaining an organized and professional appearance.

Overall, the LightSpeed Technologies CAT 860 is a powerful and flexible audio distribution system that caters to the unique needs of modern classrooms. By improving sound quality and ease of use, it enhances the overall educational experience for both students and teachers alike, making it an essential tool in today's learning environments.
Top Page Image Contents