Briggs & Stratton 020238-0 Nozzle Maintenance, Ring Maintenance, Pump Oil Maintenance, Orifice

Page 15

SpeedClean™ 2000 PSI Pressure Washer

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and adjustable nozzle extension with clean water to clear debris.

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care not to bend the screen.

3.Place o-ring into recess. Push o-ring snugly against in- line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the orifice following these instructions:

1.Shut off engine and turn off water supply.

2.Remove orifice from end of nozzle extension. Separate nozzle extension from spray gun.Twist nozzle clockwise to stream position. Using a 2mm (5/64) allen wrench, remove orifice from end of nozzle extension (Figure 14).

Figure 14 — Removing and Cleaning Orifice

Orifice

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting orifice (Figure 14).

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 15). Back flush between 30 to 60 seconds.Turn adjustable nozzle extension to stream spray and move nozzle from low to high while flushing.

Figure 15 — Backflushing the Nozzle

6.Reinstall orifice and in-line filter into nozzle extension. DO NOT overtighten orifice with allen wrench.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

9.Test pressure washer by operating with nozzle in high and low positions.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

Pump Oil Maintenance

This model does not require any pump maintenance.The pump is pre-lubricated and sealed, requiring no additional lubrication for the life of the pump.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 2000PSI Table of Contents Safety RulesEquipment Description When Transporting or Repairing Equipment Unintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Know Your Pressure Washer Unpack the Pressure Washer AssemblyCarton Contents Preparing Pressure Washer for USEInstall Wheel Kit Refer to and install the wheel kit as followsAdd Engine Oil and Fuel Connect Hose and Water Supply to Pump Checklist Before Starting EnginePressure Washer Clearance HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Pressure Washer LocationRecommended Starting Position How to Stop Your Pressure WasherTo apply detergent, follow these steps How to Use the Adjustable NozzleApplying Detergent with the Adjustable Nozzle Usage TipsThermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemSpecifications General Maintenance RecommendationsPressure Washer Maintenance Orifice Nozzle MaintenanceRing Maintenance Pump Oil MaintenanceProtecting the Pump Engine MaintenancePreparing the Unit for Storage Storing the EngineProblem Cause Correction TroubleshootingSpeedClean 2000 PSI Pressure Washer Limited Warranty Advertencia Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadCuando Añada Combustible Cuando Pruebe LA Bujía DEL Motor Precaución Conozca SU Maquina Lavadora a Presion Filtro y Tubo para Recolección de Detergente noTapa del Depósito del Aceite Llene el motor con aceite Preparando EL Lavador a Presión Para SU USO MontajeAgregar Aceite al Motor y Combustible Conecte la Manguera y el Suministro de Agua a la BombaLista de Revision Previa al Arranque del Motor Espacio Libre Alrededor del Lavadora a Presión Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónFigura 24 Posición Recomendada para el Arranque Cómo Detener su Máquina Lavadora a PresiónPara aplicar el detergente, siga los siguientes pasos Cómo Usar la Boquilla AjustableAplicación del Detergente Usando la Boquilla Ajustable Uso InclinaPara Enjuage Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoEspecificaciones Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora a Presion Boquilla Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de los Anillos OPreparando LA Unidad Para SU Almacenamiento Almacenando EL MotorProteger la Bomba Reparacion DE Averias Notas Garantía Limitada

020238-0 specifications

The Briggs & Stratton 020238-0 is a powerful and reliable generator that is designed to meet the needs of homeowners and professionals alike. This model stands out for its durability, efficiency, and advanced technology. Whether for outdoor activities, emergencies, or job sites, this generator is equipped to deliver consistent power when it is most needed.

One of the key features of the Briggs & Stratton 020238-0 is its robust engine. Powered by a reliable Briggs & Stratton engine, this generator provides dependable starting and performance. With a high-efficiency design, the engine ensures optimal fuel consumption while delivering ample power output. The generator can produce up to 5,000 running watts and 6,250 starting watts, making it suitable for running essential appliances and tools during power outages or outdoor events.

Another notable characteristic is the generator's compact and portable design. It features built-in wheels and a foldable handle, allowing for easy transport and storage. This portability makes the generator an excellent choice for camping, tailgating, or construction sites where power is required away from conventional power sources.

The Briggs & Stratton 020238-0 incorporates advanced safety features, including low-oil shutdown, which protects the engine from damage when oil levels are too low. Additionally, the generator is equipped with circuit breakers to prevent overloads and ensure safe operation. The user-friendly control panel features multiple outlets, including 120V and 120/240V options, allowing for versatile connectivity for various devices.

The generator also boasts a noise-reducing design, ensuring quieter operation compared to many other models in its class. This feature is particularly advantageous in residential areas or during nighttime use, where noise can be a concern.

In summary, the Briggs & Stratton 020238-0 is a well-rounded generator that combines power, portability, and safety. With its durable construction and advanced technologies, it serves as an invaluable tool for anyone in need of reliable electrical power. Whether for emergency backup or recreational use, this generator provides peace of mind and exceptional performance, making it an excellent investment for both casual users and professionals seeking a dependable power solution.
Top Page Image Contents