Briggs & Stratton 020261-0 Engine Maintenance, Nozzle Maintenance, Ring Maintenance, Orifice

Page 15

SpeedClean™ 2200 PSI Pressure Washer

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care not to bend the screen.

3.Place o-ring into recess. Push o-ring snugly against in- line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in manual.

6.Reinstall orifice and in-line filter into nozzle extension. DO NOT overtighten orifice with allen wrench.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

9.Test pressure washer by operating with nozzle in high and low positions.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the orifice following these instructions:

1.Shut off engine and turn off water supply.

2.Remove orifice from end of nozzle extension. Separate nozzle extension from spray gun.Twist nozzle clockwise to stream position. Using a 2mm (5/64) allen wrench, remove orifice from end of nozzle extension (Figure 20).

Figure 20 — Removing and Cleaning Orifice

Orifice

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting orifice (Figure 20).

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 21). Back flush between 30 to 60 seconds.Turn adjustable nozzle extension to stream spray and move nozzle from low to high while flushing.

Figure 21 — Backflushing the Nozzle

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

Pump Maintenance

This model does not require any pump maintenance.The pump is pre-lubricated and sealed, requiring no additional lubrication for the life of the pump.

ENGINE MAINTENANCE

See the engine operator’s manual for instructions on how to properly maintain the engine.

CAUTION

Avoid prolonged or repeated skin contact with used motor oil.

•Used motor oil has been shown to cause skin cancer in certain laboratory animals.

•Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T POLLUTE. CONSERVE RESOURCES. RETURN USED OIL TO COLLECTION CENTERS.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Advertencia 2200PSITable of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Know Your Pressure Washer High Pressure OutletPrimer Bulb Water Inlet Preparing Pressure Washer for USE AssemblyCarton Contents Attach Handle and Cleaning TankAdd Engine Oil and Fuel Attach Detergent Siphon Hose to PumpConnect Hose and Water Supply to Pump Checklist Before Starting EnginePressure Washer Clearance HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Pressure Washer LocationRecommended Starting Position How to Stop Your Pressure WasherTo attach the utility brush to the gun How to Use the Adjustable NozzleHow to Use the Floor and Utility Brushes Usage TipsThermal Relief Applying Detergent with the Adjustable NozzlePressure Washer Rinsing Automatic Cool Down SystemSpecifications General Maintenance RecommendationsPressure Washer Maintenance Pump Maintenance Engine MaintenanceNozzle Maintenance Ring MaintenanceProtecting the Pump Always wear eye protection when using PumpSaverPreparing Unit for Storage Storing the EngineProblem Cause Correction TroubleshootingSpeedClean 2200 PSI Pressure Washer Limited Warranty Símbolos de Peligro y Significados Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadCuando Añada Combustible Cuando Pruebe LA Bujía DEL Motor Precaución Conozca SU Maquina Lavadora a Presion Bomba Desarrolla alta presión de aguaTapón de Llenado y Varilla de Nivel de Aceite Permite Contenido de la Caja MontajePreparando EL Lavadora a Presión Para SU USO Desembale la Lavadora a PresiónColoque la lavadora a presión sobre una superficie nivelada Montaje de Manguera de Sifón del Detergente a la BombaAgregar Aceite al Motor y Combustible Gancho del Pistola MangueraProporcione el suministro de agua adecuado Conecte la Manguera y el Suministro de Agua a la BombaLista de Revision Previa al Arranque del Motor Deposite la gasolina adecuada en el tanque del combustibleEspacio Libre Alrededor del Lavadora a Presión Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónFigura 33 Posición Recomendada para el Arranque Cómo Detener su Máquina Lavadora a PresiónPara montar el cepillo de utilidad en la pistola Cómo Usar la Boquilla AjustableCómo Utilizar los Cepillos de Suelo y de Utilidad Uso InclinaPara aplicar el detergente, siga los siguientes pasos Aplicación del Detergente Usando la Boquilla AjustableEnjuage de la Máquina Lavadora a Presión Sistema de Enfriamiento Automático Alivio TérmicoEspecificaciones Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora Presion Mantenimiento de la Bomba Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de los Anillos OAlmacene la unidad en un lugar limpio y seco Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaReparacion DE Averias Uso comercial Uso del consumidor

020261-0 specifications

The Briggs & Stratton 020261-0 is a powerful portable generator designed to provide reliable and efficient backup power during emergencies or for outdoor activities. With a robust build and advanced technologies, this generator stands out in the market for its performance and user-friendly features.

One of the main features of the Briggs & Stratton 020261-0 is its 3000 running watts and 3750 starting watts capability. This capacity makes it suitable for powering essential appliances such as refrigerators, lights, and HVAC systems during outages, along with recreational uses like camping and tailgating. The generator is equipped with a 127cc engine that delivers efficient fuel consumption, allowing it to run for extended periods on a single tank. Its fuel tank has a capacity of 1.5 gallons, supporting a runtime of up to 9 hours at a 25% load.

In terms of technology, the Briggs & Stratton 020261-0 features a reliable recoil start system, which is both simple and effective. It is designed for easy portability, thanks to its lightweight construction and integrated handle. The generator also has a built-in circuit breaker to help protect the generator and connected devices from overload, enhancing safety during operation.

Another notable characteristic of the 020261-0 is its low noise operation. The generator is engineered for quieter functioning, making it ideal for use in residential areas or campgrounds where noise regulations may apply. Additionally, it has multiple outlets, including two household outlets and one 12V DC outlet for charging batteries, providing flexibility in powering various devices simultaneously.

Maintenance is made straightforward with the Briggs & Stratton 020261-0, as it boasts an easily accessible oil drain and a durable frame that can withstand rugged use. The generator's design prioritizes user convenience, ensuring that both setup and transport are hassle-free.

Overall, the Briggs & Stratton 020261-0 combines power, efficiency, and portability, making it an excellent choice for those in need of reliable backup power. With its solid performance, advanced safety features, and ease of use, it caters to the demands of both homeowners and outdoor enthusiasts alike, ensuring peace of mind when power outages occur or when venturing away from a traditional power source.
Top Page Image Contents