Briggs & Stratton 020261-0 manual Connect Hose and Water Supply to Pump

Page 9

SpeedClean™ 2200 PSI Pressure Washer

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 6).Tighten by hand.

Figure 6 — Connect High Pressure Hose to Spray Gun

Connect high pressure

hose here

NOTE: Remove and discard all pump shipping caps before attaching hoses.

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect the garden hose (not to exceed 50 feet in length) to the water inlet.Tighten by hand (Figure 8).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON water, point gun in a safe direction and squeeze trigger to purge pump system of air and impurities.

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 7).Tighten by hand.

Figure 7 — Connect High Pressure Hose to Pump

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate safety goggles.

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 8). Clean screen if it contains debris or have it replaced if damaged. DO NOT RUN PRESSURE WASHER IF INLET SCREEN IS DAMAGED.

Figure 8 — Connect the Garden Hose to Water Inlet

Inspect inlet

screen, DO NOT use if damaged;

clean if dirty.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all of the following.

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in the engine crankcase.

3.Add proper gasoline to fuel tank.

4.Check for properly tightened hose connections.

5.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Advertencia 2200PSITable of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Know Your Pressure Washer High Pressure OutletPrimer Bulb Water Inlet Carton Contents AssemblyAttach Handle and Cleaning Tank Preparing Pressure Washer for USEAdd Engine Oil and Fuel Attach Detergent Siphon Hose to PumpConnect Hose and Water Supply to Pump Checklist Before Starting EngineHow to Start Your Pressure Washer HOW to USE Your Pressure WasherPressure Washer Location Pressure Washer ClearanceRecommended Starting Position How to Stop Your Pressure WasherHow to Use the Floor and Utility Brushes How to Use the Adjustable NozzleUsage Tips To attach the utility brush to the gunPressure Washer Rinsing Applying Detergent with the Adjustable NozzleAutomatic Cool Down System Thermal ReliefSpecifications General Maintenance RecommendationsPressure Washer Maintenance Nozzle Maintenance Engine MaintenanceRing Maintenance Pump MaintenancePreparing Unit for Storage Always wear eye protection when using PumpSaverStoring the Engine Protecting the PumpProblem Cause Correction TroubleshootingSpeedClean 2200 PSI Pressure Washer Limited Warranty Descripción DEL Equipo Tabla DE ContenidosReglas DE Seguridad Símbolos de Peligro y SignificadosCuando Añada Combustible Cuando Pruebe LA Bujía DEL Motor Precaución Conozca SU Maquina Lavadora a Presion Bomba Desarrolla alta presión de aguaTapón de Llenado y Varilla de Nivel de Aceite Permite Preparando EL Lavadora a Presión Para SU USO MontajeDesembale la Lavadora a Presión Contenido de la CajaAgregar Aceite al Motor y Combustible Montaje de Manguera de Sifón del Detergente a la BombaGancho del Pistola Manguera Coloque la lavadora a presión sobre una superficie niveladaLista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoUbicación del Lavadora a Presión Cómo Usar SU Máquina Lavadora a PresiónCómo Darle Arranque a su Máquina Lavadora a Presión Espacio Libre Alrededor del Lavadora a PresiónFigura 33 Posición Recomendada para el Arranque Cómo Detener su Máquina Lavadora a PresiónCómo Utilizar los Cepillos de Suelo y de Utilidad Cómo Usar la Boquilla AjustableUso Inclina Para montar el cepillo de utilidad en la pistolaEnjuage de la Máquina Lavadora a Presión Aplicación del Detergente Usando la Boquilla AjustableSistema de Enfriamiento Automático Alivio Térmico Para aplicar el detergente, siga los siguientes pasosEspecificaciones Recomendaciones GeneralesMantenimiento DE LA Maquina Lavadora Presion Mantenimiento de la Boquilla Mantenimiento DEL MotorMantenimiento de los Anillos O Mantenimiento de la BombaAlmacenando EL Motor Preparando LA Unidad Para SU AlmacenamientoProteger la Bomba Almacene la unidad en un lugar limpio y secoReparacion DE Averias Uso comercial Uso del consumidor

020261-0 specifications

The Briggs & Stratton 020261-0 is a powerful portable generator designed to provide reliable and efficient backup power during emergencies or for outdoor activities. With a robust build and advanced technologies, this generator stands out in the market for its performance and user-friendly features.

One of the main features of the Briggs & Stratton 020261-0 is its 3000 running watts and 3750 starting watts capability. This capacity makes it suitable for powering essential appliances such as refrigerators, lights, and HVAC systems during outages, along with recreational uses like camping and tailgating. The generator is equipped with a 127cc engine that delivers efficient fuel consumption, allowing it to run for extended periods on a single tank. Its fuel tank has a capacity of 1.5 gallons, supporting a runtime of up to 9 hours at a 25% load.

In terms of technology, the Briggs & Stratton 020261-0 features a reliable recoil start system, which is both simple and effective. It is designed for easy portability, thanks to its lightweight construction and integrated handle. The generator also has a built-in circuit breaker to help protect the generator and connected devices from overload, enhancing safety during operation.

Another notable characteristic of the 020261-0 is its low noise operation. The generator is engineered for quieter functioning, making it ideal for use in residential areas or campgrounds where noise regulations may apply. Additionally, it has multiple outlets, including two household outlets and one 12V DC outlet for charging batteries, providing flexibility in powering various devices simultaneously.

Maintenance is made straightforward with the Briggs & Stratton 020261-0, as it boasts an easily accessible oil drain and a durable frame that can withstand rugged use. The generator's design prioritizes user convenience, ensuring that both setup and transport are hassle-free.

Overall, the Briggs & Stratton 020261-0 combines power, efficiency, and portability, making it an excellent choice for those in need of reliable backup power. With its solid performance, advanced safety features, and ease of use, it caters to the demands of both homeowners and outdoor enthusiasts alike, ensuring peace of mind when power outages occur or when venturing away from a traditional power source.
Top Page Image Contents