Briggs & Stratton 01805 Checklist Before Starting Engine, Connect Hose and Water Supply to Pump

Page 8

Pressure Washer

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 12).Tighten by hand.

Figure 12 — Connect High Pressure Hose to Spray Gun

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 13).Tighten by hand.

Figure 13 — Connect High Pressure Hose to Pump

Model 01806

OR

Model 01805

and 01806

Figure 14 — Connect the Garden Hose to Water Inlet

Inspect inlet screen,

DO NOT use if

damaged, clean if dirty.

Model 01806

OR

Inspect inlet screen,

DO NOT use if

damaged, clean if dirty.

Model 01805 and 01936

CAUTION! There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve. Damage to pressure washer resulting from disregarding this warning will not be covered by the warranty.

6.Turn ON water and squeeze trigger on gun to purge pump system of air and impurities.

CAUTION! Before starting the pressure washer, be sure you are wearing adequate eye protection.

CHECKLIST BEFORE STARTING ENGINE

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 14). Clean screen if it contains debris or replace if damaged. Refer to “O-Ring Maintenance” section on page 13 if inlet screen is damaged. DO NOT run pressure washer if inlet screen is damaged.

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 14).

Review the unit’s assembly to ensure you have performed all of the following.

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in engine crankcase.

3.Add proper fuel to fuel tank.

4.Check for properly tightened hose connections.

5.Check to make sure that there are no kinks, cuts, or damage to the high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using the pressure washer.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 01805 2500 PSI 01806 2650 PSI 01936 2550 PSI Table of Contents Safety RulesHazard Symbols and Meanings Equipment DescriptionWhen Transporting or Repairing Equipment High pressure spray may damage fragile items including glass Assembly Preparing Pressure Washer for USERemove Pressure Washer From Carton Attach Handle to UnitInstall J Hook on Accessory Tray To attach handle supplied with two L hooks Model Add Engine OilAdd Fuel Model Checklist Before Starting EngineConnect Hose and Water Supply to Pump HOW to USE Your HOW to USE NozzlesHow to Start Pressure Washer How to Stop Pressure WasherIf Unit is Equipped with Adjustable Nozzle Cleaning and Applying ChemicalFollow these instructions to change spray tips To apply detergent follow these stepsCleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal Relief Discharging the warm water onto the groundGeneral Maintenance Recommendations Pressure Washer MaintenanceNozzle Maintenance Adjustable nozzleOrifice Quick-connect spray tipsEngine Maintenance Ring MaintenancePump Maintenance Purge Pump of Air ContaminantsPreparing the Unit for Storage Storing the EngineTroubleshooting Problem Cause CorrectionOUR Equipment Tabla DE Contenidos Descripción DEL EquipoInstrucciones DE Seguridad AdvertenciaPeligro Cuando Añada CombustiblePrecaución Montaje Preparando EL Lavador a Presión Para SU USORemueva el Lavador a Presión del Empaque Conecte el ManubrioPara Conecte el Manubrio con Dos Perno L Modelo Gancho del PistolaConecte la Manguera y el Suministro de Agua a la Bomba Agregar Aceite al MotorAñada Gasolina 01806 Lista DE Revision Previa AL Arranque DEL MotorModelo Cómo Usar SU Lavadora a Presión Cómo Usar LAS BoquillasCómo Darle Arranque a su Lavadora a Presión Cómo Detener su Lavadora a PresiónSi la Unidad Está Equipada con la Boquilla Regulable Limpieza y Aplicación del QuímicoPara cambiar las boquillas Detergentes caseros podrían dañar la bombaEnjuage de la Máquina Lavadora a Presión Limpiando el Tubo de Sifón del DetergenteSistema de Enfriamiento Automático Alivio Térmico Lave de 1 a 2 minutosRecomendaciones Generales Mantenimiento DE LA Lavadora a PresionElimine el Aire y los Contaminantes de la Bomba Mantenimiento de los Anillos OBoquillas con conector rápido Para retirar el aire de la bomba, siga los siguientes pasosMantenimiento DEL Motor Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Mantenimiento de la BombaReparacion DE Averias Garantía Limitada 01806 2650 PSI Exploded View and Parts List Main Unit PSI Pressure WasherDescription Items Not Illustrated DescriptionExploded View and Parts List Pump PSI Pressure Washer

01806, 01805 specifications

Briggs & Stratton is a renowned name in the world of small engines, famously known for producing reliable and efficient power solutions for various applications. Among their impressive lineup, the models 01806 and 01805 stand out, designed to meet the demands of both consumers and professionals alike.

The 01806 model features a powerful engine with a displacement of 500cc, delivering exceptional torque and horsepower that make it suitable for a variety of applications, including lawn mowers, generators, and other outdoor equipment. Its superior performance is complemented by a user-friendly design, making it easy to operate even for those who are not mechanically inclined.

One of the key features of the Briggs & Stratton 01806 is its innovative READY START technology. This system eliminates the need for choke adjustments, allowing for effortless starting in any weather condition. Users simply pull the starter rope, and the engine fires up with ease, providing convenience for individuals who may find traditional starting methods cumbersome.

Another notable attribute of this model is its OHV (Overhead Valve) design. This technology provides better fuel efficiency, enhanced power output, and lower emissions compared to traditional flat-head engines. An OHV configuration allows for better airflow, resulting in improved combustion and overall performance.

The 01805 model also boasts similar features but comes with slight variances in horsepower and specifications tailored for specific applications. While both models emphasize durability and reliability, the 01805 is designed with lightweight construction, making it an ideal choice for equipment that requires portability without sacrificing power.

Both models feature heavy-duty components, such as a single-piece crankshaft and a contained air filtration system that protects the engine from debris, extending its operational longevity. Their compact size and clever engineering ensure they fit in a variety of applications seamlessly while providing maximum output.

In summary, the Briggs & Stratton 01806 and 01805 are exemplary models crafted for efficiency and reliability. Their advanced technologies cater to the needs of users seeking both power and ease of use. Whether for residential or commercial applications, these engines strive to uphold the prestigious reputation synonymous with the Briggs & Stratton name. The combination of reliable starting, efficient design, and durable construction ensures that these engines keep working year after year, providing outstanding performance across various tasks.
Top Page Image Contents