Briggs & Stratton 01806, 01805 owner manual HOW to USE Your, Pressure Washer, HOW to USE Nozzles

Page 9

Pressure Washer

HOW TO USE YOUR

7.On all models, attach nozzle extension to spray gun (Figure 16).Tighten by hand.

PRESSURE WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-743-4115.

How to Start Pressure Washer

To start your pressure washer for the first time, follow these instructions step-by-step.This starting information also applies if you have let the pressure washer sit idle for at least a day.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 1.0 gallons per minute more than pressure washer is rated for and no less than 20 PSI at pressure washer end of garden hose.

2.Check that high pressure hose is tightly connected to spray gun and pump. See “Preparing Pressure Washer for Use” for illustrations.

3.Make sure unit is in level position.

4.Connect garden hose to water inlet on pressure washer pump. Turn ON water.

CAUTION! DO NOT run the pump without the water supply connected and turned on.You must follow this caution or the pump will be damaged.

5.Squeeze spray gun trigger until a steady stream of water occurs.

6.For models 01806 and 01936, place quick connect spray tips in slots on the holder attached to nozzle extension (Figure 15).

Figure 15 — Install Spray Tips in Holder

Figure 16 — Connect Nozzle Extension to Spray Gun

8.Engage safety latch to spray gun trigger (Figure 17).

Figure 17 — Spray Gun with Safety Latch Engaged

Safety Latch

9.Start engine according to instructions given in engine owner’s manual.

CAUTION

Avoid injury from kickback.

•Squeeze trigger on spray gun each time recoil starter is pulled and engine fails to start.

NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.

How to Stop Pressure Washer

1.Let engine idle for two minutes.

2.Turn engine off according to instructions given in engine owner’s manual.

3.Squeeze trigger on spray gun to relieve pressure in hose.

NOTE: A small amount of water will squirt out when pressure is released.

HOW TO USE NOZZLES

You now should know how to START your pressure washer and how to STOP it.This section tells you how to adjust the spray pattern.

WARNING! NEVER adjust spray pattern when spraying. NEVER put hands in front of nozzle to test spray pattern.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 01805 2500 PSI 01806 2650 PSI 01936 2550 PSI Safety Rules Table of ContentsHazard Symbols and Meanings Equipment DescriptionWhen Transporting or Repairing Equipment High pressure spray may damage fragile items including glass Preparing Pressure Washer for USE AssemblyRemove Pressure Washer From Carton Attach Handle to UnitInstall J Hook on Accessory Tray Add Engine Oil Add FuelTo attach handle supplied with two L hooks Model Checklist Before Starting Engine Connect Hose and Water Supply to PumpModel HOW to USE Nozzles HOW to USE YourHow to Start Pressure Washer How to Stop Pressure WasherCleaning and Applying Chemical If Unit is Equipped with Adjustable NozzleFollow these instructions to change spray tips To apply detergent follow these stepsPressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal Relief Discharging the warm water onto the groundPressure Washer Maintenance General Maintenance RecommendationsAdjustable nozzle Nozzle MaintenanceOrifice Quick-connect spray tipsRing Maintenance Engine MaintenancePump Maintenance Purge Pump of Air ContaminantsStoring the Engine Preparing the Unit for StorageProblem Cause Correction TroubleshootingOUR Equipment Descripción DEL Equipo Tabla DE ContenidosInstrucciones DE Seguridad AdvertenciaCuando Añada Combustible PeligroPrecaución Preparando EL Lavador a Presión Para SU USO MontajeRemueva el Lavador a Presión del Empaque Conecte el ManubrioGancho del Pistola Para Conecte el Manubrio con Dos Perno L ModeloAgregar Aceite al Motor Añada GasolinaConecte la Manguera y el Suministro de Agua a la Bomba Lista DE Revision Previa AL Arranque DEL Motor Modelo01806 Cómo Usar LAS Boquillas Cómo Usar SU Lavadora a PresiónCómo Darle Arranque a su Lavadora a Presión Cómo Detener su Lavadora a PresiónLimpieza y Aplicación del Químico Si la Unidad Está Equipada con la Boquilla RegulablePara cambiar las boquillas Detergentes caseros podrían dañar la bombaLimpiando el Tubo de Sifón del Detergente Enjuage de la Máquina Lavadora a PresiónSistema de Enfriamiento Automático Alivio Térmico Lave de 1 a 2 minutosMantenimiento DE LA Lavadora a Presion Recomendaciones GeneralesMantenimiento de los Anillos O Elimine el Aire y los Contaminantes de la BombaBoquillas con conector rápido Para retirar el aire de la bomba, siga los siguientes pasosPreparando LA Unidad Para SU Almacenamiento Mantenimiento DEL MotorAlmacenando EL Motor Mantenimiento de la BombaReparacion DE Averias Garantía Limitada 01806 2650 PSI PSI Pressure Washer Exploded View and Parts List Main UnitDescription Items Not Illustrated DescriptionExploded View and Parts List Pump PSI Pressure Washer

01806, 01805 specifications

Briggs & Stratton is a renowned name in the world of small engines, famously known for producing reliable and efficient power solutions for various applications. Among their impressive lineup, the models 01806 and 01805 stand out, designed to meet the demands of both consumers and professionals alike.

The 01806 model features a powerful engine with a displacement of 500cc, delivering exceptional torque and horsepower that make it suitable for a variety of applications, including lawn mowers, generators, and other outdoor equipment. Its superior performance is complemented by a user-friendly design, making it easy to operate even for those who are not mechanically inclined.

One of the key features of the Briggs & Stratton 01806 is its innovative READY START technology. This system eliminates the need for choke adjustments, allowing for effortless starting in any weather condition. Users simply pull the starter rope, and the engine fires up with ease, providing convenience for individuals who may find traditional starting methods cumbersome.

Another notable attribute of this model is its OHV (Overhead Valve) design. This technology provides better fuel efficiency, enhanced power output, and lower emissions compared to traditional flat-head engines. An OHV configuration allows for better airflow, resulting in improved combustion and overall performance.

The 01805 model also boasts similar features but comes with slight variances in horsepower and specifications tailored for specific applications. While both models emphasize durability and reliability, the 01805 is designed with lightweight construction, making it an ideal choice for equipment that requires portability without sacrificing power.

Both models feature heavy-duty components, such as a single-piece crankshaft and a contained air filtration system that protects the engine from debris, extending its operational longevity. Their compact size and clever engineering ensure they fit in a variety of applications seamlessly while providing maximum output.

In summary, the Briggs & Stratton 01806 and 01805 are exemplary models crafted for efficiency and reliability. Their advanced technologies cater to the needs of users seeking both power and ease of use. Whether for residential or commercial applications, these engines strive to uphold the prestigious reputation synonymous with the Briggs & Stratton name. The combination of reliable starting, efficient design, and durable construction ensures that these engines keep working year after year, providing outstanding performance across various tasks.
Top Page Image Contents