Zenoah BCZ4000DL owner manual Operation, Starting Engine, Stopping Engine

Page 10

BCZ4000DL / BCZ4000DW / BCZ4200CL

8. Operation

STARTING ENGINE

WARNING

•The cutting head will start rotating upon the en- gine starts.

1.Feed fuel into the fuel tank and tighten the cap se- curely.

2.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine.

3.Push the primer several times until overflown fuel flows out in the clear tube.

(1)

(1) Primer

4. Move the choke lever to the closed position.

(1)

(2)

(3) (1) Choke lever

(2) Close

(3) Open

5.Set the stop switch to the “RUN” position. Place the unit on a flat, firm place.

Keep the cutting head clear of everything around it.

(1)

(1)

(1) Stop switch

6.While holding the unit firmly, pull out the starter rope quickly until engine fires.

WARNING

•The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the en- gine starts.

IMPORTANT

•Avoid pulling the rope to its end or returning it by re- leasing the knob. Such actions can cause starter fail- ures.

7.Move the choke lever downward to open the choke. And restart engine.

8.Allow the engine to warm up for a several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stop- ping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

STOPPING ENGINE

1.Release the throttle trigger and run the engine for half a minute.

2.Shift the stop switch to the STOP position.

(1)

(1)

(1) Stop switch

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle trigger.

GB-10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents BCZ4000DL BCZ4000DW BCZ4200CL Saitama, Japan 1st December Wear head, eye and ear protectionContents Parts locationModel SpecificationSymbols on the machine BCZ4000DL BCZ4000DW BCZ4200CLWorking Circumstance For safe operationWorking Condition Working PlanBefore Starting Engine Using the ProductStarting the Engine Handling Fuel MaintenanceIf Someone Comes TransportationSet up Fuel Cutting head will start rotating upon the en- gine starts OperationStarting Engine Stopping EngineCutter Application Chart Adjusting Throttle CableAdjusting Idling Speed Metal Blade UsageCutting Work Line Head Usage Cutting MethodControlling Blade Bounce Trimming Grass and WeedsMaintenance Adjusting the Line LengthAIR Filter Refilling Trimming LineBlade Fuel FilterStorage DisposalLimited warranty Troubleshooting guideCheck Probable Causes Action

BCZ4000DL specifications

The Zenoah BCZ4000DL is a remarkable addition to the world of outdoor power equipment, specifically designed for those who require efficiency and reliability in their brush cutting tasks. As part of Zenoah's esteemed lineup, the BCZ4000DL utilizes cutting-edge technologies to deliver performance that is unmatched in its category.

At the heart of the BCZ4000DL is its powerful 40cc two-stroke engine, which offers a robust power-to-weight ratio. This engine has been engineered for optimal efficiency, ensuring that users can tackle the toughest tasks without being weighed down by excessive bulk. The engine is designed with advanced ignition technology, promoting easy starting and consistent performance, even in cold conditions.

One of the standout features of the BCZ4000DL is its ergonomic design. The adjustable handle gives users the ability to customize their grip for enhanced comfort, significantly reducing fatigue during prolonged use. The unit also boasts a lightweight construction, which promotes easier maneuverability, making it an excellent choice for both professional landscapers and homeowners alike.

User convenience is further enhanced through the inclusion of a low-vibration system, which minimizes the amount of vibration transmitted to the user’s hands. This feature not only improves comfort but also allows for more precise control while cutting, contributing to cleaner and more efficient results.

The BCZ4000DL is equipped with a high-capacity fuel tank, allowing for longer operating times between refueling. This is especially valuable for larger jobs where downtime for refueling can interrupt workflow. Additionally, the model incorporates a heavy-duty cutting head that is capable of handling various types of vegetation, from tough weeds to thicker brush, making it versatile for a range of applications.

To ensure durability and longevity, the BCZ4000DL features high-quality construction materials that can withstand rigorous use in various environmental conditions. Coupled with Zenoah's commitment to sustainability, this model is designed to reduce emissions without compromising power or efficiency.

In summary, the Zenoah BCZ4000DL stands out for its powerful engine, ergonomic design, low-vibration technology, and high-capacity fuel system. This combination of features makes it an ideal choice for anyone seeking a reliable and efficient brush cutter for demanding tasks in both professional and residential settings. With the BCZ4000DL, users can take on their outdoor challenges with confidence, knowing they have a quality tool in hand.
Top Page Image Contents