Zenoah TR2002 owner manual Operation, Starting Engine, Stopping Engine

Page 11

8. Operation

STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1.Feed fuel into the fuel tank and tighten the cap se- curely.

2.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine.

3.Push the primer pump several times until overflown fuel flows out in the clear tube.

(1)Choke lever (2) Close (3) Open

(4)Purimer pump

4.Move the choke lever to the closed position.

5.Set the ignition switch to the “I” position. Set the throttle

lever to the start position (1 → 2 → 3). Place the unit on a flat, firm place.

Keep the cutting head clear of everything around it.

Stop

Start

3. Ignition switch

1

 

START

2

6. While holding the unit firmly, pull out the starter rope quickly until engine fires.

BC2003 / TR2002

 

WARNING

 

The product is equipped with a centrifugal clutch

 

mechanism, so the cutting attachment begins to ro-

 

tate as soon as the engine is started by putting the

G

throttle into the start position. When starting the en-

B

gine, place the product onto the ground in a flat clear

 

area and hold it firmly in place so as to ensure that

 

neither the cutting part nor the throttle come into con-

 

tact with any obstacle when the engine starts.

 

IMPORTANT

•Avoid pulling the rope to its end or returning it by re- leasing the knob. Such actions can cause starter fail- ures.

7.Move the choke lever downward to open the choke. And restart engine.

8.Allow the engine to warm up for a several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stop- ping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

STOPPING ENGINE

Stop Start

Ignition switch

START

1.Release the throttle lever and run the engine for half a minute.

2.Shift the ignition switch to the STOP position.

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

GB-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents BC2003 TR2002 Explanation of Symbols and Safety Warnings Contents Parts location SpecificationNever modify your machine Symbols on the machineWorking Plan For safe operationWorking Condition Working CircumstanceStarting the Engine Using the ProductBefore Starting Engine Transportation MaintenanceIf Someone Comes Handling FuelBalance Unit Set upInstalling Handle Installing Cutting Head Installing Debris GuardFuel Stopping Engine OperationStarting Engine Cutting Work Line Head Usage Adjusting Throttle CableAdjusting Idling Speed Adjusting the Line LengthFuel Filter MaintenanceAIR Filter Gear Case Replacement Plug is a NGK BPMR7ASpark Plug MufflerRefilling Trimming Line Procedures to be Performed After Every 100 Hours of USEStorage Check Probable Causes Action Troubleshooting guideLimited warranty

TR2002 specifications

The Zenoah TR2002 is a powerful and versatile two-stroke engine that has garnered attention within the realm of professional outdoor power equipment. Designed primarily for use in handheld tools, such as brush cutters and trimmers, this engine exemplifies a perfect blend of efficiency, performance, and user-friendliness.

One of the standout features of the Zenoah TR2002 is its lightweight design, which significantly enhances maneuverability during operation. Weighing considerably less than many competing models, the TR2002 allows users to work for extended periods without the frustrating fatigue that can be common with heavier equipment. This aspect is particularly appealing to both amateur gardeners and professional landscape contractors alike.

In terms of technology, the Zenoah TR2002 incorporates advanced two-stroke technology to deliver robust power output while maintaining impressive fuel efficiency. This engine is designed to minimize emissions, making it compliant with stringent environmental regulations. The TR2002 employs a unique scavenging system that ensures optimal fuel-air mixture, which translates to improved performance and reduced operational noise.

The durability of the Zenoah TR2002 cannot be overlooked. Constructed with high-quality materials, this engine is built to withstand the rigors of continuous fieldwork. Its robust design is complemented by an efficient cooling system that prevents overheating, which can be a common issue in high-performance engines.

Another defining characteristic of the Zenoah TR2002 is its user-friendly operation. The engine features easy starting technology, which minimizes the effort needed to kickstart the unit. Additionally, the ergonomic handle design enhances user comfort, enabling better control during use. This aspect is essential for achieving precision in landscaping tasks, where maneuverability and control are paramount.

Maintenance is also simplified with the Zenoah TR2002. It is designed for easy access to the air filter and spark plug, allowing for quick and efficient servicing. This design consideration significantly reduces downtime and keeps the machine running smoothly.

In conclusion, the Zenoah TR2002 stands out as a well-rounded engine option for those in need of a reliable and efficient power source for their outdoor tools. Its combination of lightweight design, advanced technologies, durability, and user-friendly features make it a valuable asset for both professional landscapers and gardening enthusiasts. Whether tackling tough brush or fine trimming, the TR2002 delivers the performance needed to get the job done efficiently.
Top Page Image Contents