Zenoah BC2310DL owner manual Operation, Starting Engine, Stopping Engine

Page 11

8. Operation

STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1.Feed fuel into the fuel tank and tighten the cap se- curely.

2.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine.

3.Push the primer pump several times until overflown fuel flows out in the clear tube.

(1)Choke lever (2) Close (3) Open

(4)Purimer pump

4.Move the choke lever to the closed position.

5.Set the ignition switch to the “I” position. Set the throttle lever to the start position (1 → 2 → 3).

Place the unit on a flat, firm place.

Keep the cutting head clear of everything around it.

Stop Start

3. Ignition switch

1

 

START

2

6. While holding the unit firmly, pull out the starter rope quickly until engine fires.

 

BC2310DL

 

 

 

 

WARNING

 

 

The product is equipped with a centrifugal clutch

 

mechanism, so the cutting attachment begins to ro-

 

tate as soon as the engine is started by putting the

G

throttle into the start position. When starting the en-

B

gine, place the product onto the ground in a flat clear

 

area and hold it firmly in place so as to ensure that

 

neither the cutting part nor the throttle come into con-

 

tact with any obstacle when the engine starts.

 

IMPORTANT

•Avoid pulling the rope to its end or returning it by re- leasing the knob. Such actions can cause starter fail- ures.

7.Move the choke lever downward to open the choke. And restart engine.

8.Allow the engine to warm up for a several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stop- ping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

STOPPING ENGINE

Stop Start

Ignition switch

START

1.Release the throttle lever and run the engine for half a minute.

2.Shift the ignition switch to the STOP position.

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

GB-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents BC2310DL E13*97/68SH2G3*2002/88*0104*04 Wear head, eye and ear protectionContents Parts location SpecificationProper usage written in the manual Symbols on the machineNever modify your machine We won’t warrant the machine, if you useWorking Plan For safe operationWorking Condition Working CircumstanceStarting the Engine Using the ProductBefore Starting Engine Transportation MaintenanceIf Someone Comes Handling FuelInstalling Cutting Head Set upInstalling Handle Installing Cutting Attachment GuardFuel Stopping Engine OperationStarting Engine Cutting Work Line Head Usage Adjusting Throttle CableAdjusting Idling Speed Adjusting the Line LengthFuel Filter MaintenanceAIR Filter Gear Case Replacement Plug is a NGK BPMR7ASpark Plug MufflerDisposal Procedures to be Performed After Every 100 Hours of USEFor safety reasons, do not use metal reinforced line StorageCheck Probable Causes Action Troubleshooting guideLimited warranty

BC2310DL specifications

The Zenoah BC2310DL is a powerful, lightweight brush cutter designed for professionals and serious garden enthusiasts. Renowned for its durability and efficiency, this model stands out in the competitive market of outdoor power equipment. Equipped with advanced features, the BC2310DL is optimized for a variety of cutting tasks, making it an ideal choice for landscaping, gardening, and general outdoor maintenance.

One of the standout characteristics of the BC2310DL is its robust engine. The brush cutter is powered by a 22.5cc two-stroke engine, delivering high performance while maintaining fuel efficiency. This engine design minimizes exhaust emissions, aligning with modern environmental standards while ensuring that the tool remains user-friendly. The lightweight construction of the BC2310DL — weighing in at just around 4.9 kg — facilitates easy maneuverability, allowing users to work for extended periods without excessive fatigue.

The ergonomic design of the Zenoah BC2310DL is also noteworthy. It features a well-balanced body with strategically placed handlebars that reduce vibration and enhance control. This makes it particularly effective for intricate tasks, such as trimming around trees and flower beds. The adjustable handle further allows users to customize the grip to suit their personal comfort levels and working styles.

In terms of technology, the BC2310DL incorporates a high-performance cutting head that can accommodate various types of cutting attachments. Users can easily switch between line trimmers and brush blades, providing versatility for tackling different types of foliage and terrain. The cutting width of the machine is ample, allowing for efficient trimming without needing excess passes.

Safety features are paramount in the BC2310DL's design. It is equipped with a protective shield that safeguards the user from flying debris while cutting. Additionally, the quick-start system ensures easy ignition with minimal effort, reducing the risk of strain on the user.

Overall, the Zenoah BC2310DL represents a blend of power, efficiency, and user-friendly design. Its combination of an advanced engine, lightweight composition, ergonomic features, and versatile cutting options make it an exceptional choice for anyone looking to maintain their outdoor spaces with optimal performance and minimal effort. Whether it's tackling overgrowth or maintaining a manicured edge, the BC2310DL proves to be a reliable partner in outdoor maintenance tasks.
Top Page Image Contents