Zenoah BC251 owner manual Operation, Starting Engine, StopStart Ignition switch, Stopping Engine

Page 10

BC251

8. Operation

STARTING ENGINE

WARNING

•The cutting head will start rotating upon the en- gine starts.

1.Feed fuel into the fuel tank and tighten the cap se- curely.

2.Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine.

3.Push the primer pump several times until overflown fuel flows out in the clear tube.

4. Move the choke lever to the closed position.

WARNING

•The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the en- gine starts.

IMPORTANT

•Avoid pulling the rope to its end or returning it by re- leasing the knob. Such actions can cause starter fail- ures.

7. Move the choke lever to the open position. And pull

out the starter rope quickly to restart engine.

(1)

A (2)

B(3)

(1) Choke lever

(2) Close

(3) Open

8. Allow the engine to warm up for a several minutes

before starting operation.

NOTE

5.Set the ignition switch to the “I” position. Set the throttle lever to the start position (1 → 2 → 3).

Place the unit on a flat, firm place.

Keep the cutting head clear of everything around it.

StopStart

3 Ignition switch

1

 

T

 

STAR

2

6. While holding the unit firmly, pull out the starter rope quickly until engine fires.

1.When restarting the engine immediately after stop- ping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

STOPPING ENGINE

1.Release the throttle lever and run the engine for half a minute.

2.Shift the ignition switch to the STOP position.

StopStart

Ignition switch

START

IMPORTANT

•Except for an emergency, avoid stopping the engine

while pulling the throttle lever.

GB-10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents BC251 Wear head, eye and ear protection Declaration of ComformityBC251 e13*97/68SH2G3*2002/88*0194*00 Contents Parts locationModel BC251 SpecificationSymbols on the machine Never modify your machineWorking Circumstance For safe operationWorking Condition Working PlanBefore Starting Engine Using the ProductStarting the Engine Handling Fuel MaintenanceIf Someone Comes TransportationInstalling Cutting Attachment Guard Set upInstalling Handle Installing Cutting HeadFuel Starting Engine StopStart Ignition switchOperation Cutting head will start rotating upon the en- gine startsAdjusting Idling Speed Cutting Work Line Head Usage Adjusting the Line LengthTrimming Grass and Weeds For safety reasons, do not use metalreinforced line MaintenanceRefilling Trimming Line Fuel Filter Replacement Plug is a NGK BPMR7AAIR Filter MufflerDisposal Procedures to be Performed After Every 100 Hours of USEStorage Gear CaseLimited warranty Troubleshooting guideCheck Probable Causes Action

BC251 specifications

The Zenoah BC251 is a highly regarded brushcutter that emphasizes efficiency and performance for both professionals and hobbyists in landscaping and gardening. This powerful machine is designed for tackling tough grass, weeds, and brush with ease, making it an essential tool for maintaining expansive lawns and gardens.

One of the standout features of the BC251 is its lightweight design, weighing in at approximately 5.5 kg (12 lbs). This makes it easy to maneuver, reducing fatigue during extended use. The ergonomic handle is also adjustable, allowing users to find the most comfortable position while operating the machine. These design choices enhance user comfort and control, especially during long periods of operation.

The engine in the Zenoah BC251 is a robust 25.4 cc, air-cooled, two-stroke engine that delivers impressive power and performance. This engine not only ensures efficient cutting but also contributes to lower emissions through its environmentally friendly design. The BC251 employs Zenoah's advanced engine technology, which improves fuel efficiency without compromising on performance. Users benefit from longer operating times and reduced fuel costs, which is a crucial consideration for professional landscapers.

Another notable characteristic of the BC251 is its versatility. It comes with a range of attachments and cutting heads, making it suitable for various tasks. Whether trimming grass along sidewalks or clearing more substantial vegetation, the BC251 can be adapted for different cutting needs. The quick-change head allows for easy switching between attachments without the need for tools, significantly improving productivity.

The vibration-dampening technology integrated into the BC251 also enhances user experience by reducing the amount of vibration transferred to the operator's hands. This feature is especially important for those who use the brushcutter for extended periods, as it minimizes fatigue and discomfort.

In summary, the Zenoah BC251 is an outstanding brushcutter known for its powerful engine, lightweight design, and versatility. With its user-friendly features and advanced technologies, it is an ideal choice for those seeking a reliable tool for maintaining gardens and landscapes. The combination of performance, comfort, and adaptability makes the BC251 a valuable addition to any landscaping toolkit.
Top Page Image Contents